2014 Hilux · Service Manual BODY

Rear Power Window RH Manual Function does not Operate with Rear Power Window Switch RH

Circuit diagnosis · Vehicles built from Jun 2011

DESCRIPTION

If the rear RH side manual up/down function does not operate, a malfunction may be present in the rear power window regulator motor assembly RH*1 or rear door window regulator sub-assembly RH*2, rear power window regulator switch assembly RH, power window regulator master switch assembly or wire harness.
  1. *1: w/o Regulator
  2. *2: w/ Regulator

WIRING DIAGRAM

B290677E02

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - BATTERY)

  1. B276367E08
    Disconnect the P11 rear power window regulator switch assembly RH connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    P11-3 (B) - Body ground
    Ignition switch ON
    11 to 14 V
    Ignition switch off
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Rear Power Window Regulator Switch Assembly RH)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH

  1. B280844
    Remove the rear power window regulator switch assembly RH.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 - 4
    2 - 3
    UP
    Below 1 Ω
    5 - 4
    2 - 1
    OFF
    Below 1 Ω
    5 - 3
    2 - 1
    DOWN
    Below 1 Ω



NG
REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH
OK


3. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH OR REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY)
  1. Disconnect the P11 rear power window regulator switch assembly RH connector.

  1. w/o Regulator:

    1. Disconnect the P8 rear power window regulator motor assembly RH connector.

  1. w/ Regulator:

    1. Disconnect the P8 rear door window regulator sub-assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    P11-5 - P8-1
    Always
    Below 1 Ω
    P11-2 - P8-2
    Always
    Below 1 Ω
    P11-5 or P8-1 - Body ground
    Always
    10 kΩ or higher
    P11-2 or P8-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

  1. w/o Regulator:

    1. B280846E03
      Remove the rear power window regulator motor assembly RH .

    2. Apply battery voltage to connector terminals 1 and 2.

    3. Check that the motor gear rotates smoothly as follows.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 2
      Battery negative (-) → 1
      Motor gear rotates clockwise
      Battery positive (+) → 1
      Battery negative (-) → 2
      Motor gear rotates counterclockwise

      Text in Illustration 
      *1
      Motor Gear
      V100135
      Clockwise
      V100136
      Counterclockwise

  1. B290680
    w/ Regulator:
    1. Remove the rear door window regulator sub-assembly RH.

    2. Apply battery voltage to connector terminals 1 and 2.

    3. Check that the motor gear rotates smoothly as follows.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 2
      Battery negative (-) → 1
      Arm of window regulator rotates clockwise (Up)
      Battery positive (+) → 1
      Battery negative (-) → 2
      Arm of window regulator rotates counterclockwise (Down)

      Text in Illustration 
      V100135
      Up
      V100136
      Down

Result 
Result
Proceed to
OK
A
NG (w/o Regulator)
B
NG (w/ Regulator)
C


B
REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

C
REPLACE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY RH
A


5. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH)
  1. Disconnect the P4 power window regulator master switch assembly connector.

  1. Disconnect the P11 rear power window regulator switch assembly RH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD, w/o Jam Protection 
    Tester Connection
    Condition
    Specified Condition
    P4-10 (U) - P11-1
    Always
    Below 1 Ω
    P4-16 (D) - P11-4
    Always
    Below 1 Ω
    P4-10 (U) or P11-1 - Body ground
    Always
    10 kΩ or higher
    P4-16 (D) or P11-4 - Body ground
    Always
    10 kΩ or higher
    for RHD, w/o Jam Protection 
    Tester Connection
    Condition
    Specified Condition
    P4-16 (U) - P11-1
    Always
    Below 1 Ω
    P4-15 (D) - P11-4
    Always
    Below 1 Ω
    P4-16 (U) or P11-1 - Body ground
    Always
    10 kΩ or higher
    P4-15 (D) or P11-4 - Body ground
    Always
    10 kΩ or higher
    w/ Jam Protection 
    Tester Connection
    Condition
    Specified Condition
    P4-18 (U) - P11-1
    Always
    Below 1 Ω
    P4-16 (D) - P11-4
    Always
    Below 1 Ω
    P4-18 (U) or P11-1 - Body ground
    Always
    10 kΩ or higher
    P4-16 (D) or P11-4 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY


← Rear Power Window LH Manual Function does not Operate with Rear Power Window Switch LH (from Jun 2011)Power Windows do not Operate at All (from Jun 2011) →