INSTALLATION
Removal / installation · Vehicles built Jun 2011 – Jul 2013
Versions by build date: Jun 2011 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
- HINT:
- Use the same procedures for the RH side and LH side.
- The procedures listed below are for the LH side.
- A bolt without a torque specification is shown in the standard bolt chart (Click here).
- Use the same procedures for the RH side and LH side.
| 1. INSTALL PLUG (for Pre-Runner) |
![]() ![]() |
Using a brass bar and hammer, tap in a plug.
| 2. INSTALL FRONT AXLE HUB OIL SEAL |
![]() ![]() |
Using a brass bar and hammer, tap in a new oil seal.
- NOTICE:
- Do not damage the spacer.
| 3. INSTALL FRONT AXLE BEARING ASSEMBLY (for 4WD) |
![]() ![]() |
Using SST and a press, press a new bearing into the axle hub.
- SST
- 09649-17010
w/ ABS:
Install the spacer and ABS rotor to the axle hub.
w/o ABS:
Install the 2 spacers to the axle hub.
| 4. INSTALL FRONT AXLE BEARING ASSEMBLY (for Pre-Runner) |
![]() ![]() |
Using SST and a press, press a new bearing into the axle hub.
- SST
- 09649-17010
w/ ABS:
Install the sensor rotor to the axle hub.
w/o ABS:
Install the spacer to the axle hub.
Using SST, install a new adjusting nut.

- SST
- 09318-12010
- Torque:
- 275 N*m{ 2,804 kgf*cm , 203 ft.*lbf }
| 5. INSTALL FRONT AXLE HUB ASSEMBLY |
![]() ![]() |
Apply MP grease to a new O-ring.
Install the new O-ring to the axle hub.
Install the dust cover and axle hub to the steering knuckle with the 4 bolts.
- Torque:
- 80 N*m{ 816 kgf*cm , 59 ft.*lbf }
| 6. INSTALL FRONT AXLE HUB NUT LH (for 4WD) |
![]() ![]() |
Install the hub nut.
- Torque:
- 235 N*m{ 2,396 kgf*cm , 173 ft.*lbf }
Install the adjusting cap and a new cotter pin.
- NOTICE:
- If the holes for the cotter pin are not aligned, tighten the nut an additional 60°.
| 7. INSTALL FRONT AXLE HUB GREASE CAP (for 4WD) |
Install a new grease cap to the axle hub.
| 8. INSTALL FRONT DISC |
| 9. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY |
![]() ![]() |
Install the disc brake caliper with the 2 bolts.
- Torque:
- 123 N*m{ 1,254 kgf*cm , 91 ft.*lbf }
Install the brake tube bracket to the steering knuckle with the bolt.

- Torque:
- 29 N*m{ 296 kgf*cm , 21 ft.*lbf }
Using SST, connect the brake tube to the disc brake caliper.

- SST
- 09023-00101
- Torque:
- 15 N*m{ 155 kgf*cm , 11 ft.*lbf } for use without SST
- 14 N*m{ 143 kgf*cm , 10 ft.*lbf } for use with SST
- HINT:
- Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
| 10. INSTALL FRONT SPEED SENSOR LH |
![]() ![]() |
Install the speed sensor with the bolt.
- Torque:
- 8.5 N*m{ 87 kgf*cm , 75 in.*lbf }
Connect the 2 clamps.
Install the speed sensor wire harness to the steering knuckle with the bolt.
- Torque:
- 32 N*m{ 326 kgf*cm , 24 ft.*lbf }
| 11. BLEED BRAKE LINE |
for TSAM Made:
(Click here)
for TMT Made:
(Click here)
w/ VSC:
(Click here)
| 12. INSTALL FRONT WHEEL |
- Torque:
- 105 N*m{ 1,071 kgf*cm , 77 ft.*lbf }
| 13. CHECK ABS SPEED SENSOR SIGNAL |
Check the ABS speed sensor signal (Click here).







