2014 Hilux · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built from Jun 2011


1. INSTALL QUARTER WINDOW GLASS LH

B114268
  1. Install the weatherstrip LH.

  1. Install the 2 hinges with the 2 bushes, 2 retainers, 2 washers and 2 screws.

  1. Install the lock with the bush, retainer and screw.

  1. B114266
    Install the glass with the 2 bolts.

    Torque:
    5.0 N*m{ 50 kgf*cm , 44 in.*lbf }

  1. B114265
    Install the 2 bolts.

    Torque:
    5.0 N*m{ 50 kgf*cm , 44 in.*lbf }


2. INSTALL ROOF SIDE GARNISH INNER UPPER LH
  1. Attach the 3 clips to install the inner upper roof side garnish.

  1. w/ Seat Cushion:

    1. Connect the rear seat belt shoulder anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    2. Attach the 2 claws to close the rear seat belt shoulder anchor cover.


3. INSTALL QUARTER PILLAR GARNISH LH
  1. Attach the 2 clips to install the quarter pillar garnish.

  1. Connect the front seat belt shoulder anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Attach the 4 claws to install the front seat belt shoulder anchor cover.


4. INSTALL QUARTER INSIDE TRIM BOARD LH
  1. Attach the 7 clips, 3 guides and 4 claws to install the quarter inside trim board.

  1. Connect the front seat outer belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


5. INSTALL QUARTER TRIM PANEL LOWER LH
  1. Attach the 7 clips, 3 guides and 4 claws to install the quarter inside trim board.

  1. Connect the front seat outer belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


6. INSTALL REAR NO. 1 SEAT BELT ASSEMBLY OUTER LH

B113856E02
  1. Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf } for bolt A

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf } for bolt B

  1. B087825E02
    Install the bolt and close the cover as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B089599E02
    Install the floor anchor with the bolt, as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B114992E01
    Install the floor anchor with the bolt, as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


7. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

B084917E01

NOTICE:
Do not disassemble the retractor.

  1. w/o Pretensioner single cab and extra cab:
    Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B084922E01
    w/o Pretensioner Double cab:
    Align the claws with the seat belt positioning holes and install the ELR of the seat belt with the bolt as shown in the illustration.

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf }

  1. B113098E03
    w/ Pretensioner:
    Install the bolt and seat belt.

    Torque:
    4.8 N*m{ 49 kgf*cm , 42 in.*lbf } for bolt A

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf } for bolt B

  1. B114993
    w/ Pretensioner:
    Connect the pretensioner connector as shown in the illustration.

  1. B084915E01
    Single cab:
    Install the anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Close the cover.

  1. B084920E01
    Extra cab and double cab:
    Install the anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. Install the cap.

  1. B085691E01
    Single cab:
    Install the quarter trim panel lower. Then install the seat belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B085692E01
    Extra cab:
    Install the quarter inside trim board. Then install the seat belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B085693E01
    Double cab:
    Install the anchor of the seat belt with the built-in bolt after installing the center pillar garnish lower.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


8. INSTALL REAR SEATBACK ASSEMBLY

  1. B276916
    Place the rear seatback assembly in the cabin.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Attach the 2 hooks to the vehicle body.

  1. Install the rear seatback assembly with the 2 bolts.

    Torque:
    39 N*m{ 398 kgf*cm , 29 in.*lbf }


9. INSTALL BACK PANEL GARNISH LOWER
  1. Attach the 5 clips, 2 guides and 6 claws to install the lower back panel garnish.


10. INSTALL REAR SEAT CUSHION ASSEMBLY LH

  1. B288345
    Attach the 2 hooks.

  1. B288346
    Attach the hook to install the rear seat cushion assembly LH.


11. INSTALL REAR SEAT CUSHION ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


12. INSTALL BACK PANEL GARNISH UPPER
  1. Attach the 5 clips, 2 guides and 6 claws to install the lower back panel garnish.


13. INSTALL FRONT DOOR OPENING TRIM LH

B276973E01
  1. Align the paint mark on the front door opening trim with the mark position on the vehicle and install the front door opening trim as shown in the illustration.

    Text in Illustration 
    *1
    Paint Mark
    *2
    Mark Position


14. INSTALL FRONT DOOR SCUFF PLATE LH
  1. Attach the 4 clips and 8 claws to install the front door scuff plate.


15. INSTALL FRONT SEAT ASSEMBLY (Separate Seat Type)
  1. Install front seat assembly (Click here).


16. INSTALL FRONT SEAT ASSEMBLY (Bench Seat Type)
  1. Install front seat assembly (Click here).


17. CHECK FOR LEAKS AND REPAIR
← REMOVAL (from Jun 2011)PARTS LOCATION (from Jun 2011) →