2014 Hilux · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built from Jun 2011

HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. REMOVE FRONT SEAT ASSEMBLY (Bench Seat Type)
  1. Remove front seat assembly (Click here).


2. REMOVE FRONT SEAT ASSEMBLY (Separate Seat Type)
  1. Remove front seat assembly (Click here).


3. REMOVE FRONT DOOR SCUFF PLATE LH

B276994E01
  1. Put protective tape around the front door scuff plate.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 4 clips and 8 claws and remove the front door scuff plate.


4. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

B276994E01
  1. Put protective tape around the front door scuff plate.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 4 clips and 8 claws and remove the front door scuff plate.


5. REMOVE BACK PANEL GARNISH UPPER

B276964
  1. Detach the 4 claws and 5 clips and remove the upper back panel garnish.


6. REMOVE REAR SEAT CUSHION ASSEMBLY LH

  1. B288340
    Operate the rear seat cushion lock hook release lever and pull up the rear seat cushion assembly LH to detach the hook.
    Text in Illustration 
    V100135
    Pull Up
    V100136
    Release

  1. B288341
    Detach the 2 hooks and rear seat cushion assembly LH.


7. REMOVE REAR SEAT CUSHION ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


8. REMOVE BACK PANEL GARNISH LOWER

B276965
  1. Detach the 6 claws, 2 guides and 5 clips and remove the lower back panel garnish.


9. REMOVE REAR SEATBACK ASSEMBLY

  1. B276915
    Remove the 2 bolts.

  1. Lift up the rear seatback assembly in the direction indicated by the arrow to detach the 2 hooks from the vehicle body. Then remove the rear seatback assembly.

    NOTICE:
    Be careful not to damage the vehicle body.


10. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH

B087764E01
  1. Using a moulding remover, detach the 2 claws and remove the outer seat track bracket cover.


11. REMOVE REAR NO. 1 SEAT BELT ASSEMBLY OUTER LH

B089293E04
  1. Remove the bolt and floor anchor.

  1. B086292E03
    Using a screwdriver, detach the 2 claws and open the seat belt anchor cover.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the bolt.

  1. B113849E01
    Remove the bolt and seat belt.


12. REMOVE QUARTER INSIDE TRIM BOARD LH

B276966
  1. Remove the bolt and disconnect the front seat outer belt floor anchor.

  1. B276968
    Detach the 4 claws, 3 guides and 7 clips and remove the quarter inside trim board.


13. REMOVE QUARTER PILLAR GARNISH LH

B276930E01
  1. Using a screwdriver, detach the 4 claws and remove the front seat belt shoulder anchor cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. )Remove the bolt and disconnect the front seat belt shoulder anchor.

  1. B276967
    Detach the 2 clips and remove the quarter pillar garnish.


14. REMOVE ROOF SIDE GARNISH INNER UPPER LH

B276936E01
  1. w/ Seat Cushion:

    1. Using a screwdriver, detach the 2 claws and open the rear seat belt shoulder anchor cover.

      HINT:
      Tape the screwdriver tip before use.

      Text in Illustration 
      *1
      Protective Tape

    2. Remove the bolt and disconnect the rear seat belt shoulder anchor.

  1. B276969
    Detach the 3 clips and remove the inner upper roof side garnish.


15. REMOVE QUARTER WINDOW ASSEMBLY LH

B114265

NOTICE:
  1. When separating the glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.
  2. Procedures must be performed with 2 people, where the second person supports the glass.

  1. Remove the 2 bolts.

  1. B114266
    Remove the 2 bolts.

  1. B114267E01
    Remove the glass as shown in the illustration.

  1. Remove the screw, bush, retainer and lock.

  1. Remove the 2 screws, 2 washers, 2 retainers, 2 bushes and 2 hinges.

  1. Remove the weatherstrip LH.

← COMPONENTS (from Jun 2011)INSTALLATION (from Jun 2011) →