2014 Hilux · Service Manual ENGINE

P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit

Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012

Also covers:

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

HINT:
  1. This is the repair procedure for the accelerator pedal position sensor.
  2. This electrical throttle system does not use a throttle cable.
  3. The accelerator pedal position sensor is a non-contact type.

The accelerator pedal position sensor is mounted on the accelerator pedal and detects the opening angle of the accelerator pedal. Since this sensor is electronically controlled with Hall-effect elements, accurate control and reliability can be obtained. It has 2 sensors to detect the accelerator position and malfunctions of the accelerator position sensor.
In the accelerator pedal position sensor, the voltage applied to pedal terminals VPA and VPA2 of the ECM changes between 0 V and 5 V in proportion to the opening angle of the accelerator pedal. VPA is used to detect the actual accelerator pedal opening angle, which is used for the engine control. VPA2 is used to detect information about the opening angle, which is used for detecting malfunctions.
The ECM judges the current opening angle of the accelerator pedal using signals from terminals VPA and VPA2, and the ECM controls the throttle motor based on these signals.
G036462E06
DTC No.
DTC Detection Condition
(All of following are 1 trip detection logic)
Trouble Area
P2120
Condition (a) continues for 0.5 sec. or more:
(a) VPA is 0.4 V or less or VPA is 4.8 V or more
  1. Accelerator pedal position sensor
  2. Accelerator pedal
  3. Accelerator pedal rod (arm) deformed
  4. ECM
P2122
VPA is 0.4 V or less for 0.5 sec. or more when VPA2 output indicates that accelerator pedal is opened
  1. Accelerator pedal position sensor
  2. Open in VCPA circuit
  3. VPA circuit open or ground short
  4. Accelerator pedal
  5. Accelerator pedal rod (arm) deformed
  6. ECM
P2123
Condition (a) continues for 2.0 sec. or more:
(a) VPA is 4.8 V or more
  1. Accelerator pedal position sensor
  2. Open in EPA circuit
  3. Accelerator pedal
  4. Accelerator pedal rod (arm) deformed
  5. ECM
P2125
Condition (a) continues for 0.5 sec. or more:
(a) (VPA2 is 1.2 V or less) or (VPA2 is 4.8 V or more)
  1. Accelerator pedal position sensor
  2. Accelerator pedal
  3. Accelerator pedal rod (arm) deformed
  4. ECM
P2127
VPA2 is 1.2 V or less for 0.5 sec. or more when VPA output indicates that accelerator pedal is opened
  1. Accelerator pedal position sensor
  2. Open in VCP2 circuit
  3. VPA2 circuit open or ground short
  4. Accelerator pedal
  5. Accelerator pedal rod (arm) deformed
  6. ECM
P2128
Conditions (a) and (b) continue for 2.0 sec. or more:
(a) VPA2 is 4.8 V or more
(b) VPA is 0.4 V to 3.45 V
  1. Accelerator pedal position sensor
  2. Open in EPA2 circuit
  3. Accelerator pedal
  4. Accelerator pedal rod (arm) deformed
  5. ECM
P2138
Condition (a) or (b) continues for 2.0 sec. or more:
(a) Difference between VPA and VPA2 is 0.02 V or less
(b) VPA is 0.4 V or less and VPA2 is 1.2 V or less
  1. VPA and VPA2 circuit are short-circuited
  2. Accelerator pedal position sensor
  3. Accelerator pedal
  4. Accelerator pedal rod (arm) deformed
  5. ECM

HINT:
Accelerator pedal positions are expressed as voltages.


WIRING DIAGRAM

A119981E04

INSPECTION PROCEDURE

NOTICE:
If the ECM is replaced, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (ACCEL SENS. NO.1 VOLT % AND ACCEL SENS. NO.2 VOLT %)

  1. FI07052E07
    Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.

  1. Read the values.

    Standard:
    Accelerator Pedal
    Accel Sens. No.1 Volt %
    Accel Sens. No.2 Volt %
    Released
    10 to 22%
    24 to 40%
    Depressed
    52 to 90%
    68 to 99%



OK
Go to step 5
NG


2. CHECK HARNESS AND CONNECTOR (ECM - ACCELERATOR PEDAL POSITION SENSOR)
A111102E04
  1. Disconnect the A13 sensor connector.

  1. Disconnect the E5 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    A13-1 (VCP2) - E5-27 (VCP2)
    Below 1 Ω
    A13-2 (EPA2) - E5-29 (EPA2)
    Below 1 Ω
    A13-3 (VPA2) - E5-23 (VPA2)
    Below 1 Ω
    A13-4 (VCPA) - E5-26 (VCPA)
    Below 1 Ω
    A13-5 (EPA) - E5-28 (EPA)
    Below 1 Ω
    A13-6 (VPA) - E5-22 (VPA)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    A13-1 (VCP2) or E5-27 (VCP2) - Body ground
    10 kΩ or higher
    A13-2 (EPA2) or E5-29 (EPA2) - Body ground
    10 kΩ or higher
    A13-3 (VPA2) or E5-23 (VPA2) - Body ground
    10 kΩ or higher
    A13-4 (VCPA) or E5-26 (VCPA) - Body ground
    10 kΩ or higher
    A13-5 (EPA) or E5-28 (EPA) - Body ground
    10 kΩ or higher
    A13-6 (VPA) or E5-22 (VPA) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK ECM (VCPA, VCP2 VOLTAGE)
A096639E09
  1. Disconnect the A13 sensor connector.

  1. Turn the ignition switch ON.

  1. Measure the voltage of the ECM connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    E5-26 (VCPA) - E5-28 (EPA)
    4.5 to 5.0 V
    E5-27 (VCP2) - E5-29 (EPA2)
    4.5 to 5.0 V



NG
REPLACE ECM
OK


4. REPLACE ACCELERATOR PEDAL ROD ASSEMBLY
  1. Replace accelerator pedal rod assembly (Click here).


NEXT


5. READ IF OUTPUT DTC RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Allow the engine to idle for 15 seconds.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Read the DTC (Click here).

    Result:
    Display (DTC output)
    Proceed to
    P2120, P2122, P2123, P2125, P2127, P2128 or P2138 is output again
    A
    Not output
    B



B
END
A

REPLACE ECM


← P2009 Intake Manifold Runner Control Circuit Low (Bank 1) (+ P2010) (from Aug 2014)P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit (+ 6 more codes) (Aug 2012 – Jul 2013) →