2014 Hilux · Service Manual TRANSMISSION

U0100 Lost Communication with ECM / PCM "A"

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The Transmission Control Module (TCM) and ECM perform 2-way communications with each other via the Controller Area Network (CAN). The TCM sends signals to the ECM concerning required engine rpm, required engine torques, warning indicators in the combination meter, DTCs and other data. The ECM sends signals to the TCM concerning engine rpm, opening angles of the throttle valve, temperature of the intake air and engine coolant, engine torques, and other data.
If the TCM cannot communicate with the ECM, the TCM will conclude that there is a malfunction in the CAN system, illuminate the MIL and store a DTC.
DTC Code
DTC Detection Condition
Trouble Area
U0100
No communication from ECM for certain period of time (1-trip detection logic)
  1. Open or short in TCM and ECM circuit
  2. TCM
  3. ECM

WIRING DIAGRAM

C239208E04

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

NOTICE:
If the ECM is replaced, the new ECM needs initialization.


1. CHECK ECM (+B VOLTAGE, E1 GROUND)
C238415E13
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E5-1 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E7-7 (E1) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Component with harness connected
(ECM)


NG
GO TO ECD SYSTEM (ECM POWER SOURCE CIRCUIT) (Click here)
OK


2. CHECK TCM (IG2 VOLTAGE, E1 GROUND)
C212050E28
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    T38-6 (IG2) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    T19-1 (E1) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Component with harness connected
(TCM)


NG
GO TO ECU POWER SOURCE CIRCUIT
OK


3. CHECK HARNESS AND CONNECTOR (ECM - TCM)
  1. Disconnect the E6 ECM connector.

  1. Disconnect the T38 TCM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E6-22 (CAN+) - T38-21 (CAN+)
    Always
    Below 1 Ω
    E6-21 (CAN-) - T38-20 (CAN-)
    Always
    Below 1 Ω
    E6-22 (CAN+) or T38-21 (CAN+) - Body ground
    Always
    10 kΩ or higher
    E6-21 (CAN-) or T38-20 (CAN-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CONFIRM DTC
  1. Clear the DTC.

  1. Replace the TCM (Click here).

    HINT:
    Replace the TCM with a TCM from a normally functioning vehicle of the same model.

  1. Start the engine.

  1. Read the DTCs.

    Result:
    Result
    Proceed to
    U0100 is output
    A
    U0100 is not output
    B



B
REPLACE TCM
A

REPLACE ECM


← U0100 Lost Communication with ECM / PCM "A" (Aug 2013 – Jul 2014)ECU Power Source Circuit (from Aug 2012) →