2014 Hilux · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013


1. INSTALL FRONT EXHAUST PIPE ASSEMBLY

  1. A107610
    Using a vernier caliper, measure the free length of the compression spring.

    Minimum length:
    40 mm (1.57 in.)

    If the length is less than the minimum, replace the compression spring.

  1. Install the front pipe to the pipe support.

  1. A099436E03
    Install a new gasket to the exhaust manifold.

    NOTICE:
    1. Be careful with the installation direction of the gasket.
    2. Do not reuse the gasket.
    3. To ensure a proper seal, do not use the front pipe to force the gasket onto the exhaust manifold.

    HINT:
    Using a plastic-faced hammer, uniformly strike the gasket so that the gasket and exhaust manifold are properly fit.

  1. Install the front pipe with the 2 compression springs and 2 bolts. Alternately tighten the bolts in several passes.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }


2. INSTALL HEATED OXYGEN SENSOR (w/ Secondary Air Injection System)
  1. for 2WD: (Click here)
  2. for 4WD: (Click here)

3. INSTALL HEATED OXYGEN SENSOR (w/o Secondary Air Injection System)

  1. G039121E01
    Using SST, install the sensor.
    SST
    09224-00010  

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf } for use without SST
    40 N*m{ 408 kgf*cm , 30 ft.*lbf } for use with SST

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).

  1. A112091
    Attach the 3 wire clamps to the vehicle body.

  1. Connect the sensor connector.


4. INSTALL AIR FUEL RATIO SENSOR (w/ Secondary Air Injection System)

  1. G039121E01
    Using SST, install the sensor.
    SST
    09224-00010  

    Torque:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf } for use without SST
    40 N*m{ 408 kgf*cm , 30 ft.*lbf } for use with SST

    HINT:
    Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).

  1. A112091
    Attach the 3 wire clamps to the vehicle body.

  1. Connect the sensor connector.


5. INSTALL CENTER EXHAUST PIPE ASSEMBLY
  1. Install the center pipe to the 3 pipe supports.

  1. Install a new gasket and the center pipe to the front pipe with the 2 bolts and 2 nuts. Alternately tighten the bolts in several passes.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    NOTICE:
    Do not reuse the gasket.


6. INSTALL TAILPIPE ASSEMBLY
  1. Install the tailpipe to the pipe support.

  1. Install a new gasket and the tailpipe to the center pipe with the 2 bolts and 2 nuts. Alternately tighten the bolts in several passes.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    NOTICE:
    Do not reuse the gasket.


7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

8. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.


9. CHECK FOR EXHAUST GAS LEAKS
If gas is leaking, tighten the problem areas to stop the leak. Replace damaged parts as necessary.
← INSTALLATION (Jun 2011 – Jul 2012)INSTALLATION (from Aug 2013) →