INSTALLATION
Removal / installation · Vehicles built Jun 2011 – Jul 2012
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
| 1.
INSTALL FRONT EXHAUST PIPE ASSEMBLY |
 |
- Using a vernier caliper, measure the free length of the compression spring.
- Minimum length:
- 40 mm (1.57 in.)
If the length is less than the minimum, replace the compression spring.
Install the front pipe to the pipe support.
- Install a new gasket to the exhaust manifold.
- NOTICE:
- Be careful with the installation direction of the gasket.
- Do not reuse the gasket.
- To ensure a proper seal, do not use the front pipe to force the gasket onto the exhaust manifold.
- HINT:
- Using a plastic-faced hammer, uniformly strike the gasket so that the gasket and exhaust manifold are properly fit.
Install the front pipe with the 2 compression springs and 2 bolts. Alternately tighten the bolts in several passes.
-
Torque:
- 43 N*m{
438 kgf*cm
, 32 ft.*lbf
}
| 2.
INSTALL HEATED OXYGEN SENSOR (w/ Secondary Air Injection System) |
 |
- for 2WD: (Click here)
- for 4WD: (Click here)
| 3.
INSTALL HEATED OXYGEN SENSOR (w/o Secondary Air Injection System)
|
 |
- Using SST, install the sensor.
- SST
- 09224-00010
-
Torque:
- 44 N*m{
449 kgf*cm
, 32 ft.*lbf
}
for use without SST
- 40 N*m{
408 kgf*cm
, 30 ft.*lbf
}
for use with SST
- HINT:
- Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
- Attach the 3 wire clamps to the vehicle body.
Connect the sensor connector.
| 4.
INSTALL AIR FUEL RATIO SENSOR (w/ Secondary Air Injection System)
|
 |
- Using SST, install the sensor.
- SST
- 09224-00010
-
Torque:
- 44 N*m{
449 kgf*cm
, 32 ft.*lbf
}
for use without SST
- 40 N*m{
408 kgf*cm
, 30 ft.*lbf
}
for use with SST
- HINT:
- Use a torque wrench with a fulcrum length of 30 cm (11.81 in.).
- Attach the 3 wire clamps to the vehicle body.
Connect the sensor connector.
| 5.
INSTALL CENTER EXHAUST PIPE ASSEMBLY |
 |
Install the center pipe to the 3 pipe supports.
Install a new gasket and the center pipe to the front pipe with the 2 bolts and 2 nuts. Alternately tighten the bolts in several passes.
-
Torque:
- 48 N*m{
489 kgf*cm
, 35 ft.*lbf
}
- NOTICE:
- Do not reuse the gasket.
| 6.
INSTALL TAILPIPE ASSEMBLY |
 |
Install the tailpipe to the pipe support.
Install a new gasket and the tailpipe to the center pipe with the 2 bolts and 2 nuts. Alternately tighten the bolts in several passes.
-
Torque:
- 48 N*m{
489 kgf*cm
, 35 ft.*lbf
}
- NOTICE:
- Do not reuse the gasket.
| 7.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
|
| 8.
PERFORM INITIALIZATION |
 |
Perform initialization (Click here).
- NOTICE:
- Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.
| 9.
CHECK FOR EXHAUST GAS LEAKS |
 |
If gas is leaking, tighten the problem areas to stop the leak. Replace damaged parts as necessary.