INSTALLATION
Removal / installation · Vehicles built Aug 2012 – Jul 2013
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
| 1.
INSTALL INPUT SHAFT FRONT BEARING |
 |
- Using SST and a hammer, tap in a new bearing.
- SST
- 09304-12012
- HINT:
- After installing the bearing to the hub, make sure that it rotates smoothly.
Install 2 new bolts.
-
Torque:
- 123 N*m{
1,250 kgf*cm
, 90 ft.*lbf
}
| 2.
INSTALL CLUTCH DISC ASSEMBLY |
 |
Insert SST into the clutch disc. Then insert the SST (together with the clutch disc) into the flywheel.
- SST
- 09301-00110
- NOTICE:
- Take care not to insert the clutch disc facing the wrong direction.
| 3.
INSTALL CLUTCH COVER ASSEMBLY |
 |
- Align the matchmarks on the clutch cover and flywheel.
Tighten the 6 bolts as described below.
Determine the first bolt to be tightened by choosing the bolt closest to the knock pin.
Uniformly tighten the 6 bolts in diametrically opposite pairs relative to the position of the first bolt. Use the illustration as a reference.
-
Torque:
- 19 N*m{
195 kgf*cm
, 14 in.*lbf
}
Lightly move SST up and down, and right and left.
- SST
- 09301-00110
Check that the disc is in the center, and then tighten the bolts.
| 4.
INSPECT AND ADJUST CLUTCH COVER ASSEMBLY |
 |
- Using a dial indicator with roller instrument, measure the diaphragm spring tip alignment.
- Maximum misalignment:
- 0.9 mm (0.035 in.)
-
If the alignment is as specified, use SST to adjust the diaphragm spring tip alignment.
- SST
- 09333-00013
| 5.
INSTALL RELEASE FORK SUPPORT |
 |
Install the release fork support to the manual transmission unit.
| 6.
INSTALL RELEASE BEARING HUB CLIP |
 |
Install the release bearing hub clip to the release bearing.
| 7.
INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY |
 |
- Apply Multemp 8158 Grease or equivalent to the following areas:
- The contact surfaces of the release fork and release bearing hub.
- The contact surfaces of the release fork and push rod.
- The pivot points of the release fork.
- Grease:
- Multemp 8158 Grease or equivalent
Install the release fork to the release bearing.
| 8.
INSTALL CLUTCH RELEASE BEARING ASSEMBLY |
 |
- Apply clutch spline grease to the input shaft spline.
- Grease:
- Toyota Genuine Clutch Spline Grease or equivalent
Install the release fork (with release bearing) to the manual transmission.
- NOTICE:
- After the installation, move the fork forward and backward to check that the release bearing slides smoothly.
| 9.
INSTALL CLUTCH RELEASE FORK BOOT |
|
| 10.
INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY |
 |
Install the manual transmission unit.
G58 manual transmission (Click here).
G58F manual transmission (Click here).
| 11.
INSTALL FRONT PROPELLER SHAFT ASSEMBLY (4WD) |
 |
Install the front propeller shaft (Click here).
| 12.
INSTALL REAR PROPELLER SHAFT ASSEMBLY |
 |
Install the rear propeller shaft (Click here).
| 13.
INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY (4WD) |
 |
-
Torque:
- 29 N*m{
296 kgf*cm
, 21 ft.*lbf
}
| 14.
INSTALL NO. 2 ENGINE COVER SUB-ASSEMBLY (4WD) |
 |
-
Torque:
- 29 N*m{
296 kgf*cm
, 21 ft.*lbf
}
| 15.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
|
| 16.
PERFORM INITIALIZATION |
 |
Perform initialization (Click here ).
- NOTICE:
- Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.