2014 Hilux · Service Manual TRANSMISSION

INSTALLATION

Removal / installation · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013


1. INSTALL INPUT SHAFT FRONT BEARING (for 1KD-FTV, 2KD-FTV)

  1. Q007151E01
    Using SST and a hammer, tap in a new bearing.
    SST
    09304-12012  

    HINT:
    After installing the bearing to the hub, make sure that it rotates smoothly.

  1. Install 2 new bolts.
    for 1KD-FTV: (Click here)
    for 2KD-FTV: (Click here)


2. INSTALL INPUT SHAFT FRONT BEARING (for 1TR-FE, 2TR-FE)

  1. Q007151E01
    Using SST and a hammer, tap in a new bearing.
    SST
    09304-12012  

    HINT:
    After installing the bearing to the hub, make sure that it rotates smoothly.

  1. Install 2 new bolts.
    for 1TR-FE: (Click here)
    for 2TR-FE: (Click here)


3. INSTALL CLUTCH DISC ASSEMBLY

  1. C290849E01
    Insert SST into the clutch disc. Then insert the SST (together with the clutch disc) into the flywheel.
    SST
    09301-00110  

    NOTICE:
    Take care not to insert the clutch disc facing the wrong direction.


4. INSTALL CLUTCH COVER ASSEMBLY

  1. D029623E01
    Align the matchmarks on the clutch cover and flywheel.

  1. Tighten the 6 bolts as described below.

    1. Determine the first bolt to be tightened by choosing the bolt closest to the knock pin.

    2. Uniformly tighten the 6 bolts in diametrically opposite pairs relative to the position of the first bolt. Use the illustration as a reference.

      Torque:
      19 N*m{ 195 kgf*cm , 14 in.*lbf }

  1. Lightly move SST up and down, and right and left.

    SST
    09301-00110  

  1. Check that the disc is in the center, and then tighten the bolts.


5. INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

  1. D029624E01
    Using a dial indicator with roller instrument, measure the diaphragm spring tip alignment.

    Maximum misalignment:
    0.5 mm (0.020 in.)


    1. D029625E01
      If the alignment is not as specified, use SST to adjust the diaphragm spring tip alignment.
    SST
    09333-00013  


6. INSTALL RELEASE FORK SUPPORT
  1. Install the release fork support to the manual transmission unit.


7. INSTALL RELEASE BEARING HUB CLIP
  1. Install the release bearing hub clip to the release bearing.


8. INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

  1. C132684
    Apply Multemp 8158 Grease or equivalent to the following areas:
    1. The contact surfaces of the release fork and release bearing hub.
    2. The contact surfaces of the release fork and push rod.
    3. The pivot points of the release fork.

      Grease:
      Multemp 8158 Grease or equivalent

  1. Install the release fork to the release bearing.


9. INSTALL CLUTCH RELEASE BEARING ASSEMBLY

  1. D029659E01
    Apply clutch spline grease to the input shaft spline.

    Grease:
    Toyota Genuine Clutch Spline Grease or equivalent

  1. Install the release fork (with release bearing) to the manual transmission.

    NOTICE:
    After the installation, move the fork forward and backward to check that the release bearing slides smoothly.


10. INSTALL CLUTCH RELEASE FORK BOOT

11. INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY
for G50/G55 manual transmission: (Click here).
for R150F/R151F/R156F manual transmission: (Click here).
for R150/R151/R156 manual transmission: (Click here).
← INSTALLATION (Aug 2012 – Jul 2013)COMPONENTS (from Jun 2011) →