2014 Hilux · Service Manual TRANSMISSION

REMOVAL

Removal / installation · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2013 from Aug 2013


1. DISCONNECT BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


2. REMOVE NO.1 ENGINE UNDER COVER

3. REMOVE NO.2 ENGINE UNDER COVER (for Pre-Runner)

4. REMOVE NO.3 ENGINE UNDER COVER (for Pre-Runner)

5. REMOVE NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY (except Pre-Runner)

G034583E01
  1. Remove the 4 nuts, 4 bolts and frame crossmember.


6. DISCONNECT HEATED OXYGEN SENSOR

7. REMOVE EXHAUST PIPE
  1. Remove the exhaust pipe (Click here).


8. REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY
  1. for TMT Made:
    Remove the propeller shaft with center bearing assembly (Click here).

  1. for TSAM Made:
    Remove the propeller shaft with center bearing assembly (Click here).


9. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    28 N*m{ 285 kgf*cm , 21 ft.*lbf }


10. REMOVE MANIFOLD STAY

F050360E01
  1. Remove the 3 bolts and manifold stay.


11. REMOVE NO. 2 MANIFOLD STAY

F050356E01
  1. Remove the 3 bolts and manifold stay.


12. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH
  1. Remove the 6 nuts, exhaust manifold and gasket.


13. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH
  1. Remove the 6 nuts, exhaust manifold and gasket.


14. DISCONNECT OIL COOLER TUBE

C111240
  1. Using a union nut wrench, disconnect the inlet tube and outlet tube.

  1. C111230
    Remove the 2 bolts and 2 clamps.


15. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

C111231
  1. Remove the nut and disconnect the control cable.

  1. Remove the clip and disconnect the control cable.


16. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

C111232
  1. Remove the 2 bolts and control cable bracket from the transmission.


17. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

C112848
  1. Support the transmission with a transmission jack.


18. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

G034517E01
  1. Remove the 4 set bolts of the No. 1 engine mounting insulator rear.

  1. Remove the 4 nuts, 4 bolts and frame crossmember.


19. REMOVE NO. 1 ENGINE MOUNTING INSULATOR REAR

C238609
  1. Remove the 4 bolts, ground cable and engine mounting insulator.


20. DISCONNECT CONNECTOR

C112849
  1. Tilt the transmission downward.

    NOTICE:
    Make sure the cooling fan does not contact the fan shroud.

  1. Transmission side:
    Disconnect the connectors.

    1. Disconnect the park/neutral position switch connector.

    2. Disconnect the transmission wire connector.

    3. Disconnect the 3 speed sensor connectors.


21. DISCONNECT WIRE HARNESS

22. REMOVE STARTER ASSEMBLY
  1. Remove the starter assembly (Click here).


23. REMOVE FLYWHEEL HOUSING SIDE COVER

F050352E01
  1. Remove the flywheel housing side cover from the cylinder block.


24. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

C111234
  1. Turn the crankshaft to gain access to each bolt.

  1. Hold the crankshaft pulley bolt with a wrench and remove the 6 torque converter clutch mounting bolts.

  1. C111235
    Remove the 9 bolts.

  1. Separate and remove the automatic transmission assembly.


25. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY
← REMOVAL (Jun 2011 – Jul 2013)INSTALLATION (Jun 2011 – Jul 2012) →