2014 Hilux · Service Manual TRANSMISSION

P0500 Vehicle Speed Sensor Malfunction

Diagnostic trouble codes · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Aug 2012 – Jul 2013 from Aug 2013

DESCRIPTION

The vehicle speed sensor (SPD1) outputs a 4-pulse signal for every revolution of the rotor shaft, which is rotated by the transmission output shaft via the driven gear. After this signal is converted into a more precise rectangular waveform by the waveform shaping circuit inside the combination meter, it is then transmitted to the TCM. The TCM determines the vehicle speed based on the frequency of these pulse signals.
DTC Code
DTC Detection Condition
Trouble Area
P0500
All conditions below are detected 500 times or more continuously (2-trip detection logic):
(a) No signal from vehicle speed sensor (SPD1) is input to TCM while 48 pulses of speed sensor (SP2) signal are sent
(b) Vehicle speed is 9 km/h (6 mph) or more for at least 4 seconds
(c) PNP switch is off (shift lever not in P or N)
  1. Open or short in vehicle speed sensor (SPD1) circuit
  2. Vehicle speed sensor (SPD1)
  3. Combination meter assembly
  4. TCM

WIRING DIAGRAM

C122128E20

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / ECT / Data List.

  1. Drive the vehicle.

  1. Read the value displayed on the tester.

    ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed/
    Min.: 0 km/h (0 mph)
    Max.: 255 km/h (158 mph)
    Actual vehicle speed
    Speed indicated on speedometer

    OK:
    Vehicle speed displayed on tester and speedometer display are equal.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS

2. CHECK COMBINATION METER ASSEMBLY (SPD1 SIGNAL WAVEFORM)

  1. C217466E09
    Remove the combination meter assembly with the connector(s) still connected.

  1. Move the shift lever to N.

  1. Jack up the vehicle.

  1. Turn the ignition switch to ON.

  1. Check the signal waveform according to the condition(s) in the table below.

    Measurement Condition:
    Terminal No. (Symbol)
    Tool Setting
    Condition
    C25-6 - Body ground
    5 V/DIV., 20 msec./DIV.
    Vehicle speed 20 km/h (12 mph)

    OK:
    The waveform is displayed as shown in the illustration.

    Text in Illustration 
    *a
    Component with harness connected
    (Combination Meter Assembly)



NG
GO TO METER / GAUGE SYSTEM (SPEEDOMETER MALFUNCTION) (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TCM)
  1. Disconnect the C25 combination meter assembly connector.

  1. Disconnect the T38 TCM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C25-6 - T38-25 (SPD1)
    Always
    Below 1 Ω
    C25-6 or T38-25 (SPD1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TCM


← DIAGNOSTIC TROUBLE CODE CHART (from Aug 2014)P0500 Vehicle Speed Sensor Malfunction (from Aug 2013) →