2014 Hilux · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. PRECAUTION (w/ Airbag System)

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Airbag System)

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE REAR SEAT ASSEMBLY
(Click here)

4. REMOVE FRONT DOOR SCUFF PLATE LH

B276926E01
  1. Put protective tape around the front door scuff plate LH.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 7 claws and 3 clips, and remove the front door scuff plate LH.


5. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure described for the LH side.


6. REMOVE FRONT DOOR OPENING TRIM LH

B276985
  1. Remove the front door opening trim LH.


7. REMOVE FRONT DOOR OPENING TRIM RH

HINT:
Use the same procedure described for the LH side.


8. REMOVE ASSIST GRIP PLUG LH (w/ Assist Grip)

B277720E01

HINT:
Use the same procedure for both assist grip plugs LH.

  1. Using a screwdriver, detach the 2 claws and remove the assist grip plug LH.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Tape


9. REMOVE ASSIST GRIP PLUG RH (w/ Assist Grip)

HINT:
Use the same procedure described for the LH side.


10. REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)

B206335

HINT:
Use the same procedure for both front assist grip sub-assemblies.

  1. Remove the 2 screws and front assist grip sub-assembly.


11. REMOVE FRONT PILLAR GARNISH LH

B276932
  1. Detach the 2 clips and 2 guides and remove the front pillar garnish LH.

  1. B289825E01
    w/ Curtain Shield Airbag:
    Protect the curtain shield airbag assembly.

    1. Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish LH is removed.

      Text in Illustration 
      *1
      Protective Cover
      *2
      Adhesive Tape


12. REMOVE FRONT PILLAR GARNISH RH

HINT:
Use the same procedure described for the LH side.


13. REMOVE REAR DOOR SCUFF PLATE LH

B277892E01
  1. Put protective tape around the rear door scuff plate LH.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 7 claws and 2 clips, and remove the rear door scuff plate LH.


14. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedure described for the LH side.


15. REMOVE REAR DOOR OPENING TRIM LH

B276987
  1. Remove the rear door opening trim LH.


16. REMOVE REAR DOOR OPENING TRIM RH

HINT:
Use the same procedure described for the LH side.


17. REMOVE LOWER CENTER PILLAR GARNISH LH

B276978
  1. Remove the bolt and disconnect the front seat outer belt floor anchor.

  1. B276929
    Detach the 2 claws, 2 guides and 2 clips and remove the lower center pillar garnish LH.


18. REMOVE LOWER CENTER PILLAR GARNISH RH

HINT:
Use the same procedure described for the LH side.


19. REMOVE CENTER PILLAR GARNISH LH

B276930E01
  1. Using a screwdriver, detach the 4 claws and remove the front seat belt shoulder anchor cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Tape

  1. Remove the bolt and disconnect the front seat belt shoulder anchor.

  1. B276931
    Detach the clip.

  1. Pull the center pillar garnish LH in the direction indicated by the arrow in the illustration to detach the guide and remove the center pillar garnish LH.


20. REMOVE CENTER PILLAR GARNISH RH

HINT:
Use the same procedure described for the LH side.


21. REMOVE UPPER BACK PANEL GARNISH (w/o Rear Center Seat Belt)

B276979
  1. Detach the 4 claws and 5 clips and remove the upper back panel garnish.


22. REMOVE BACK PANEL TRIM (w/ Rear Center Seat Belt)

B353736
  1. Detach the 5 claws and disconnect the seat belt guide.

  1. B353737
    Remove the 4 clips.

  1. Detach the 2 claws and 9 clips and remove the back panel trim.


23. REMOVE LOWER QUARTER TRIM PANEL LH

B276982
  1. w/o Rear Center Seat Belt:

    1. Detach the claw and 3 clips and remove the lower quarter trim panel LH.

  1. B353738
    w/ Rear Center Seat Belt:

    1. Detach the claw and 3 clips and remove the lower quarter trim panel LH.


24. REMOVE LOWER QUARTER TRIM PANEL RH

HINT:
Use the same procedure described for the LH side.


25. REMOVE QUARTER INSIDE TRIM BOARD LH

B276936E01
  1. Using a screwdriver, detach the 2 claws and open the rear seat belt shoulder anchor cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Tape

  1. Remove the bolt and disconnect the rear seat belt shoulder anchor.

  1. B276981
    w/o Rear Center Seat Belt:

    1. Detach the 4 clips and remove the quarter inside trim board LH.

  1. B353739
    w/ Rear Center Seat Belt:

    1. Detach the 4 clips and remove the quarter inside trim board LH.


26. REMOVE QUARTER INSIDE TRIM BOARD RH

HINT:
Use the same procedure described for the LH side.


27. REMOVE MAP LIGHT ASSEMBLY

  1. E289365
    Remove the 2 screws.

  1. Detach the claw and 2 guides and remove the map light assembly.

  1. Disconnect the connector.


28. REMOVE NO. 1 ROOM LIGHT ASSEMBLY

  1. B085012
    Using a screwdriver, detach the 4 claws and remove the lens.

    HINT:
    Tape the screwdriver tip before use.

  1. B085593
    Remove the 2 screws and room light.

  1. Disconnect the lamp connector.


29. REMOVE VISOR ASSEMBLY LH

B266814
  1. Detach the guide.

  1. Remove the 2 screws and visor assembly LH.


30. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


31. REMOVE VISOR HOLDER LH

B266815
  1. Remove the screw.

  1. Detach the 2 claws and remove the visor holder LH.


32. REMOVE VISOR HOLDER RH

HINT:
Use the same procedure described for the LH side.


33. REMOVE ASSIST GRIP (w/ Assist Grip)

B277629E01

HINT:
Use the same procedure for all assist grips.

  1. Using a screwdriver, detach the 4 claws and open the 2 covers.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Tape

  1. B206336
    Remove the 2 screws and assist grip.


34. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY
(Click here)

35. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

B278242
  1. Detach the 2 claws, 3 clips and 3 guides and remove the lower instrument panel finish panel.


36. REMOVE NO. 2 HEATER TO REGISTER DUCT

  1. E225181
    Remove the 3 clips and No. 2 heater to register duct.


37. REMOVE NO. 1 HEATER TO REGISTER DUCT

E225182
  1. Remove the clip.

  1. Detach the 3 claws and remove the No. 1 heater to register duct.


38. REMOVE NO. 3 HEATER TO REGISTER DUCT

E225183
  1. Remove the clip.

  1. Detach the 4 claws and remove the No. 3 heater to register duct.


39. REMOVE DEFROSTER NOZZLE ASSEMBLY (w/ Defroster)

  1. E225184
    Using a screwdriver, detach the 4 clips and remove the defroster nozzle assembly.


40. REMOVE BACK WINDOW GLASS
(Click here)

41. REMOVE ROOF HEADLINING ASSEMBLY

B283170
  1. Detach the 5 clamps from the front pillar.

  1. for LHD:

    1. B206359
      Disconnect the connectors and detach the 4 clamps.

    2. B288744E01
      Using a clip remover, remove the clips.
      Text in Illustration 
      *A
      w/o Assist Grip

    3. Remove the roof headlining assembly as shown in the illustration.

      NOTICE:
      Be careful not to damage the roof headlining assembly when removing it.

  1. for RHD:

    1. Disconnect the connectors and detach the 5 clamps.

      B276943

    2. B288745E01
      Using a clip remover, remove the clips.
      Text in Illustration 
      *A
      w/o Assist Grip

    3. Remove the roof headlining assembly as shown in the illustration.

      NOTICE:
      Be careful not to damage the roof headlining assembly when removing it.


42. REMOVE FRONT SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

B276948
  1. Detach the 2 claws and remove the front side rail spacer LH.


43. REMOVE FRONT SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

HINT:
Use the same procedure described for the LH side.


44. REMOVE SIDE RAIL SPACER (for LHD, w/o Curtain Shield Airbag)

B278255
  1. Detach the 2 claws and remove the side rail spacer.


45. REMOVE SIDE RAIL SPACER (for RHD, w/o Curtain Shield Airbag)

HINT:
Use the same procedure described for LHD vehicles.


46. REMOVE REAR NO. 2 SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

B276949

HINT:
Use the same procedure for both rear No. 2 side rail spacers LH.

  1. Detach the 2 claws and remove the rear No. 2 side rail spacer LH.


47. REMOVE REAR NO. 2 SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

HINT:
Use the same procedure described for the LH side.


48. REMOVE REAR NO. 3 SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)

B276980
  1. Detach the 3 claws and remove the rear No. 3 side rail spacer LH.


49. REMOVE REAR NO. 3 SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)

HINT:
Use the same procedure described for the LH side.

← REMOVAL (Aug 2012 – Jul 2013)DISASSEMBLY (from Jun 2011) →