Home › BODY › INSTRUMENT PANEL › UPPER INSTRUMENT PANEL
REMOVAL
Removal / installation · Vehicles built from Aug 2013
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
HINT:
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1.
TABLE OF BOLT, SCREW AND NUT
All bolts, screws and clips relevant to installing and removing the instrument panel are shown along with their alphabetical code in the table.
2.
PRECAUTION (w/ Airbag System)
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here ).
3.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Airbag System)
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here ).
4.
REMOVE STEERING WHEEL ASSEMBLY
(Click here )
5.
REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL
Remove the clip <C>.
Detach the 2 claws and 3 guides and remove the No. 1 instrument cluster finish panel.
6.
REMOVE COMBINATION METER ASSEMBLY
Remove the 3 screws.
Disconnect the connectors, detach the clamp and remove the combination meter.
7.
REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
for Manual Air Conditioning System:
Put protective tape around the center instrument cluster finish panel.
Text in Illustration
*1
Protective Tape
Using a moulding remover, detach the 10 claws and 4 clips.
Detach the 4 claws and disconnect the air conditioner control.
Disconnect the connectors and remove the center instrument cluster finish panel.
for Automatic Air Conditioning System:
Put protective tape around the center instrument cluster finish panel.
Text in Illustration
*1
Protective Tape
Using a moulding remover, detach the 8 claws and 4 clips.
Disconnect the connectors and remove the center instrument cluster finish panel.
8.
REMOVE RADIO RECEIVER ASSEMBLY (w/ Audio)
for Radio Receiver Type: (Click here )
for Radio and Display Type: (Click here )
9.
REMOVE RADIO TUNER OPENING COVER (w/o Audio)
Remove the 4 screws and radio tuner opening cover.
10.
REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY (w/ Front Passenger Airbag)
Slightly bend the upper part of the glove compartment door to release the 2 stoppers and open the glove compartment door until it is horizontal.
Text in Illustration
*1
Stopper
Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.
Text in Illustration
*1
Hinge
11.
REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (w/ Front Passenger Airbag)
Disconnect the connector from the airbag.
NOTICE:
When handling the airbag connector, do not damage the airbag wire harness.
Remove the 2 bolts.
Detach the clamp from the bracket.
Detach the 12 claws and remove the airbag.
12.
REMOVE FRONT NO. 1 ASSIST GRIP PLUG LH (w/ Assist Grip)
HINT:
Use the same procedure for both assist grip plugs LH.
Using a screwdriver, detach the 2 claws and remove the assist grip plug LH.
HINT:
Tape the screwdriver tip before use.
Text in Illustration
*1
Tape
13.
REMOVE FRONT NO. 1 ASSIST GRIP PLUG RH (w/ Assist Grip)
HINT:
Use the same procedure described for the LH side.
14.
REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)
HINT:
Use the same procedure for both front assist grip sub-assemblies.
Remove the 2 screws and front assist grip sub-assembly.
15.
REMOVE FRONT PILLAR GARNISH LH
Remove the part of the front door opening trim attached to the front pillar garnish.
Detach the 2 clips and 2 guides and remove the front pillar garnish.
w/ Curtain Shield Airbag: Protect the curtain shield airbag assembly.
Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.
NOTICE:
Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.
Text in Illustration
*1
Protective Cover
*2
Adhesive Tape
16.
REMOVE FRONT PILLAR GARNISH RH
HINT:
Use the same procedure described for the LH side.
17.
REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY
for LHD:
Put protective tape around the upper instrument panel.
Remove the 2 bolts <A> and 2 screws <B>.
Using a screwdriver, detach the 8 claws and 5 guides and remove the upper instrument panel.
HINT:
Tape the screwdriver tip before use.
Text in Illustration
*A
w/o Front Passenger Airbag
*B
w/ Front Passenger Airbag
*1
Protective Tape
*2
Bolt <A>
*3
Screw <B>
-
-
for RHD:
Put protective tape around the upper instrument panel.
Remove the 2 bolts <A> and 2 screws <B>.
Using a screwdriver, detach the 8 claws and 5 guides and remove the upper instrument panel.
HINT:
Tape the screwdriver tip before use.
Text in Illustration
*A
w/o Front Passenger Airbag
*B
w/ Front Passenger Airbag
*1
Protective Tape
*2
Bolt <A>
*3
Screw <B>
-
-