2014 Hilux · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here)


3. REMOVE FRONT SEAT ASSEMBLY LH
  1. w/ Front Seat Side Airbag:
    (Click here)

  1. for Separate Seat Type:
    (Click here)


4. REMOVE FRONT SEAT ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


5. REMOVE FRONT DOOR SCUFF PLATE LH

B276994E01
  1. Put protective tape around the front door scuff plate.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 4 clips and 8 claws and remove the front door scuff plate.


6. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure described for the LH side.


7. REMOVE FRONT DOOR OPENING TRIM LH

B276972
  1. Remove the front door opening trim.


8. REMOVE FRONT DOOR OPENING TRIM RH

HINT:
Use the same procedure described for the LH side.


9. REMOVE FRONT NO. 1 ASSIST GRIP PLUG LH (w/ Assist Grip)

B277720E01

HINT:
Use the same procedure for both front No. 1 assist grip plugs.

  1. Using a screwdriver, detach the 2 claws and remove the front No. 1 assist grip plug.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


10. REMOVE FRONT NO. 1 ASSIST GRIP PLUG RH (w/ Assist Grip)

HINT:
Use the same procedure described for the LH side.


11. REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY (w/ Assist Grip)

B206335

HINT:
Use the same procedure for both front assist grips.

  1. Remove the 2 screws and front assist grip.


12. REMOVE FRONT PILLAR GARNISH LH

B276932
  1. Detach the 2 clips and 2 guides and remove the front pillar garnish.

  1. B289825E01
    w/ Curtain Shield Airbag:
    Protect the curtain shield airbag assembly.

    1. Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

      Text in Illustration 
      *1
      Protective Cover
      *2
      Adhesive Tape


13. REMOVE FRONT PILLAR GARNISH RH

HINT:
Use the same procedure described for the LH side.


14. REMOVE REAR SEAT CUSHION ASSEMBLY LH (w/ Seat Cushion)

  1. B288340
    Operate the rear seat cushion lock hook release lever and pull up the rear seat cushion assembly LH to detach the hook.
    Text in Illustration 
    V100135
    Pull Up
    V100136
    Release

  1. B288341
    Detach the 2 hooks and rear seat cushion assembly LH.


15. REMOVE REAR SEAT CUSHION ASSEMBLY RH (w/ Seat Cushion)

HINT:
Use the same procedures described for the LH side.


16. REMOVE UPPER BACK PANEL GARNISH

B276964
  1. Detach the 4 claws and 5 clips and remove the upper back panel garnish.


17. REMOVE REAR SEATBACK ASSEMBLY

  1. B276915
    Remove the 2 bolts.

  1. Lift up the rear seatback assembly in the direction indicated by the arrow to detach the 2 hooks from the vehicle body. Then remove the rear seatback assembly.

    NOTICE:
    Be careful not to damage the vehicle body.


18. REMOVE LOWER BACK PANEL GARNISH

B276965
  1. Detach the 6 claws, 2 guides and 5 clips and remove the lower back panel garnish.


19. REMOVE QUARTER INSIDE TRIM BOARD LH

B276966
  1. Remove the bolt and disconnect the front seat outer belt floor anchor.

  1. B276968
    Detach the 4 claws, 3 guides and 7 clips and remove the quarter inside trim board.


20. REMOVE QUARTER INSIDE TRIM BOARD RH

HINT:
Use the same procedure described for the LH side.


21. REMOVE QUARTER PILLAR GARNISH LH

B276930E01
  1. Using a screwdriver, detach the 4 claws and remove the front seat belt shoulder anchor cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. )Remove the bolt and disconnect the front seat belt shoulder anchor.

  1. B276967
    Detach the 2 clips and remove the quarter pillar garnish.


22. REMOVE QUARTER PILLAR GARNISH RH

HINT:
Use the same procedure described for the LH side.


23. REMOVE INNER UPPER ROOF SIDE GARNISH LH

B276936E01
  1. w/ Seat Cushion:

    1. Using a screwdriver, detach the 2 claws and open the rear seat belt shoulder anchor cover.

      HINT:
      Tape the screwdriver tip before use.

      Text in Illustration 
      *1
      Protective Tape

    2. Remove the bolt and disconnect the rear seat belt shoulder anchor.

  1. B276969
    Detach the 3 clips and remove the inner upper roof side garnish.


24. REMOVE INNER UPPER ROOF SIDE GARNISH RH

HINT:
Use the same procedure described for the LH side.


25. REMOVE MAP LIGHT ASSEMBLY (w/ Map Light)

  1. E289365
    Remove the 2 screws.

  1. Detach the claw and 2 guides and remove the map light assembly.

  1. Disconnect the connector.


26. REMOVE NO. 1 ROOM LIGHT ASSEMBLY

  1. B085012
    Using a screwdriver, detach the 4 claws and remove the lens.

    HINT:
    Tape the screwdriver tip before use.

  1. B085593
    Remove the 2 screws and room light.

  1. Disconnect the lamp connector.


27. REMOVE VISOR ASSEMBLY LH

B266814
  1. Detach the guide.

  1. Remove the 2 screws and visor.


28. REMOVE VISOR ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


29. REMOVE VISOR HOLDER LH

B266815
  1. Remove the screw.

  1. Detach the 2 claws and remove the visor holder.


30. REMOVE VISOR HOLDER RH

HINT:
Use the same procedures described for the LH side.


31. REMOVE ASSIST GRIP (w/ Assist Grip)

B277629E01
  1. Using a screwdriver, detach the 4 claws and open the 2 covers.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. B206336
    Remove the 2 screws and assist grip.


32. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY
(Click here)

33. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

B278242
  1. Detach the 2 claws, 3 clips and 3 guides and remove the lower instrument panel finish panel.


34. REMOVE NO. 2 HEATER TO REGISTER DUCT

  1. E225181
    Remove the 3 clips and No. 2 heater to register duct.


35. REMOVE NO. 1 HEATER TO REGISTER DUCT

E225182
  1. Remove the clip.

  1. Detach the 3 claws and remove the No. 1 heater to register duct.


36. REMOVE NO. 3 HEATER TO REGISTER DUCT

E225183
  1. Remove the clip.

  1. Detach the 4 claws and remove the No. 3 heater to register duct.


37. REMOVE DEFROSTER NOZZLE ASSEMBLY

  1. E225184
    Using a screwdriver, detach the 4 clips and remove the defroster nozzle assembly.


38. REMOVE ROOF HEADLINING ASSEMBLY

B283170
  1. Detach the 5 clamps from the front pillar.

  1. for LHD:

    1. B206359
      Disconnect the connectors and detach the 4 clamps.

    2. B288827
      Using a clip remover, remove the 5 clips.

    3. B288828
      Remove the roof headlining as shown in the illustration.

      NOTICE:
      Be careful not to damage the roof headlining when removing it.

  1. for RHD:

    1. Disconnect the connectors and detach the 5 clamps.

      B276943

    2. B206156E01
      Using a clip remover, remove the clips.
      Text in Illustration 
      *1
      w/o Assist Grip

    3. B276970
      Remove the roof headlining as shown in the illustration.

      NOTICE:
      Be careful not to damage the roof headlining when removing it.


39. REMOVE FRONT SIDE RAIL SPACER LH

B276948
  1. Detach the 2 claws and remove the front side rail spacer.


40. REMOVE FRONT SIDE RAIL SPACER RH

HINT:
Use the same procedure described for the LH side.


41. REMOVE SIDE RAIL SPACER (for LHD)

B288829
  1. Detach the 2 claws and remove the side rail spacer.


42. REMOVE SIDE RAIL SPACER (for RHD)

HINT:
Use the same procedure described for the LHD.


43. REMOVE REAR NO. 2 SIDE RAIL SPACER LH

B276949
  1. Detach the 2 claws and remove the rear No. 2 side rail spacer.


44. REMOVE REAR NO. 2 SIDE RAIL SPACER RH

HINT:
Use the same procedure described for the LH side.


45. REMOVE REAR NO. 3 SIDE RAIL SPACER LH

B276971
  1. Detach the 4 claws and remove the rear No. 3 side rail spacer.


46. REMOVE REAR NO. 3 SIDE RAIL SPACER RH

HINT:
Use the same procedure described for the LH side.

← REMOVAL (Aug 2012 – Jul 2013)DISASSEMBLY (from Jun 2011) →