2014 Hilux · Service Manual BODY

INSTALLATION

Removal / installation · Vehicles built Aug 2012 – Jul 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. INSTALL FUEL FILLER OPENING LID LOCK RETAINER

B277117
  1. Install the fuel filler opening lid lock retainer and turn it counterclockwise as shown in the illustration.


2. INSTALL FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY

  1. for LHD:

    1. B277115
      Install the cable and turn the fuel filler opening lid lock retainer clockwise as shown in the illustration.

    2. Attach the cable to the clamps shown in the illustration.

    3. Install the grommet to the vehicle body.

    4. Install the fuel lid lock open lever.

      B278269E01

      Text in Illustration 
      *1
      Fuel Lid Lock Open Lever
      *2
      Grommet

  1. for RHD:

    1. B277115
      Install the cable and turn the fuel filler opening lid lock retainer clockwise as shown in the illustration.

    2. Attach the cable to the clamps shown in the illustration.

    3. Install the grommet to the vehicle body.

    4. Install the fuel lid lock open lever.

      B277214E01

      Text in Illustration 
      *1
      Fuel Lid Lock Open Lever
      *2
      Grommet


3. INSTALL REAR WHEEL HOUSE LINER LH
  1. Install the rear wheel house liner.


4. INSTALL REAR NO. 1 WHEEL OPENING EXTENSION SUB-ASSEMBLY LH (w/ Over Fender)
  1. Install 11 new clips to the rear No. 1 wheel opening extension.

  1. Attach the 11 clips to install the rear No. 1 wheel opening extension.

  1. w/ Mudguard:
    Install the 5 screws.

  1. w/o Mudguard:
    Install the 8 screws.


5. INSTALL FRONT FLOOR CARPET ASSEMBLY
  1. Install the front floor carpet.


6. INSTALL LOWER QUARTER TRIM PANEL LH
  1. Attach the 3 clips and claw to install the lower quarter trim panel.

  1. Install the front door opening trim.

  1. Connect the front seat outer belt floor anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


7. INSTALL COWL SIDE TRIM BOARD LH (for LHD)
  1. Attach the 2 clips to install the cowl side trim board.

  1. Install the clip.

  1. Install the front door opening trim.


8. INSTALL COWL SIDE TRIM BOARD RH (for RHD)

HINT:
Use the same procedure described for the LH side.


9. INSTALL FRONT DOOR SCUFF PLATE LH
  1. Attach the 4 clips and 8 claws to install the front door scuff plate.


10. INSTALL FRONT DOOR SCUFF PLATE RH (for RHD)

HINT:
Use the same procedure described for the LH side.


11. INSTALL UPPER BACK PANEL GARNISH
  1. Attach the 5 clips, 4 guides and 4 claws to install the upper back panel garnish.


12. INSTALL CONSOLE BOX ASSEMBLY (w/ Console Box)
(Click here)

13. INSTALL FRONT SEAT ASSEMBLY LH
  1. w/ Front Seat Side Airbag:
    (Click here)

  1. for Separate Seat Type:
    (Click here)


14. INSTALL FRONT SEAT ASSEMBLY RH
  1. w/ Front Seat Side Airbag:

    HINT:
    Use the same procedure described for the LH side.

  1. for Separate Seat Type:

    HINT:
    Use the same procedure described for the LH side.

  1. for Bench Seat Type:
    (Click here)

← INSTALLATION (Jun 2011 – Jul 2012)INSTALLATION (from Aug 2013) →