2014 Hilux · Service Manual BODY

REMOVAL

Removal / installation · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. REMOVE FRONT SEAT ASSEMBLY LH
  1. w/ Front Seat Side Airbag:
    (Click here)

  1. for Power Seat:
    (Click here)

  1. for Separate Seat Type:
    (Click here)


2. REMOVE FRONT SEAT ASSEMBLY RH
  1. w/ Front Seat Side Airbag:

    HINT:
    Use the same procedure described for the LH side.

  1. for Power Seat:

    HINT:
    Use the same procedure described for the LH side.

  1. for Separate Seat Type:

    HINT:
    Use the same procedure described for the LH side.

  1. for Bench Seat Type:
    (Click here )


3. REMOVE REAR SEAT ASSEMBLY
(Click here)

4. REMOVE CONSOLE BOX ASSEMBLY (w/ Console Box)
(Click here)

5. REMOVE UPPER BACK PANEL GARNISH (w/o Rear Center Seat Belt)

B276979
  1. Detach the 4 claws and 5 clips and remove the upper back panel garnish.


6. REMOVE BACK PANEL TRIM (for RHD, w/ Rear Center Seat Belt)

B353736
  1. Detach the 5 claws and disconnect the seat belt guide.

  1. B353737
    Remove the 4 clips.

  1. Detach the 2 claws and 9 clips and remove the back panel trim.


7. REMOVE FRONT DOOR SCUFF PLATE LH

B276926E01
  1. Put protective tape around the front door scuff plate LH.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 7 claws and 3 clips, and remove the front door scuff plate LH.


8. REMOVE FRONT DOOR SCUFF PLATE RH (for RHD)

HINT:
Use the same procedure described for the LH side.


9. REMOVE REAR DOOR SCUFF PLATE LH

B277892E01
  1. Put protective tape around the rear door scuff plate LH.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 7 claws and 2 clips, and remove the rear door scuff plate LH.


10. REMOVE COWL SIDE TRIM BOARD LH (for LHD)

B277609
  1. Remove the part of the front door opening trim attached to the cowl side trim board.

  1. Remove the clip.

  1. Detach the 2 clips and remove the cowl side trim board.


11. REMOVE COWL SIDE TRIM BOARD RH (for RHD)

HINT:
Use the same procedure described for the LH side.


12. REMOVE LOWER CENTER PILLAR GARNISH LH

B276978
  1. Remove the bolt and disconnect the front seat outer belt floor anchor.

  1. B276929
    Remove the part of the front door opening trim and rear door opening trim attached to the lower center pillar garnish.

  1. Detach the 2 claws, 2 guides and 2 clips and remove the lower center pillar garnish.


13. REMOVE LOWER QUARTER TRIM PANEL LH

B276982
  1. Remove the part of the rear door opening trim attached to the lower quarter trim panel.

  1. Detach the claw and 3 clips and remove the lower quarter trim panel.


14. REMOVE FRONT FLOOR CARPET ASSEMBLY
  1. Partially remove the floor carpet.

    HINT:
    It is not necessary to fully remove the floor carpet. Partially remove it so that the lock control cable can be removed in a later step.


15. REMOVE REAR NO. 1 WHEEL OPENING EXTENSION SUB-ASSEMBLY LH (w/ Over Fender)

  1. w/ Mudguard:

    1. B277559E01
      Put protective tape around the No. 1 rear wheel opening extension.
      Text in Illustration 
      *1
      Protective Tape

    2. Remove the 5 screws.

  1. w/o Mudguard:

    1. B291253E01
      Put protective tape around the No. 1 rear wheel opening extension.
      Text in Illustration 
      *1
      Protective Tape

    2. Remove the 8 screws.

  1. B277560
    Detach the 11 clips and remove the No. 1 rear wheel opening extension.

  1. Remove the 11 clips from the vehicle body.


16. REMOVE REAR WHEEL HOUSE LINER LH
  1. Partially remove the rear wheel house liner.

    HINT:
    It is not necessary to fully remove the liner. Partially remove it so that the lock control cable can be removed in a later step.


17. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY

  1. for LHD:

    1. Remove the fuel lid lock open lever.

    2. Remove the grommet from the vehicle body.

    3. Detach the cable from the clamps shown in the illustration.

      B278268E01

      Text in Illustration 
      *1
      Fuel Lid Lock Open Lever
      *2
      Grommet

    4. B277114
      Turn the fuel filler opening lid lock retainer counterclockwise and remove the fuel lid lock control cable from the fuel filler opening lid lock retainer.

  1. for RHD:

    1. Remove the fuel lid lock open lever.

    2. Remove the grommet from the vehicle body.

    3. Detach the cable from the clamps shown in the illustration.

      B277215E01

      Text in Illustration 
      *1
      Fuel Lid Lock Open Lever
      *2
      Grommet

    4. B277114
      Turn the fuel filler opening lid lock retainer counterclockwise and remove the fuel lid lock control cable from the fuel filler opening lid lock retainer.


18. REMOVE FUEL FILLER OPENING LID LOCK RETAINER

B277116
  1. Turn the fuel filler opening lid lock retainer clockwise and remove the fuel filler opening lid lock retainer as shown in the illustration.

← REMOVAL (Aug 2012 – Jul 2013)INSTALLATION (Jun 2011 – Jul 2012) →