2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.


1. REMOVE ENGINE ASSEMBLY
(Click here)

2. REMOVE NO. 1 TIMING BELT COVER
  1. Remove the bolt and water hose clamp.

  1. Remove the wire harness clamp.

  1. A148169
    Remove the 6 bolts and timing belt cover.


3. REMOVE TIMING BELT

  1. A070549E02
    Turn the crankshaft clockwise and align the timing marks as shown in the illustration.

  1. A070550E01
    Uniformly loosen the 2 bolts and remove the timing belt tensioner.

  1. Remove the timing belt.

  1. Using a 10 mm hexagon wrench, remove the bolt, timing belt idler and washer.

    HINT:
    A148170E01
    1. When turning the camshaft while the timing belt is removed, turn the crankshaft 90° counterclockwise.
    2. When installing the timing belt, return the camshaft to the timing marks and then turn the crankshaft clockwise until it aligns with the timing marks, as shown in the illustration.


4. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

5. REMOVE VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY

  1. I034100E02
    Disconnect the connector.

  1. Remove the 2 bolts and viscous with magnet clutch heater assembly.


6. REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY
  1. Remove the 4 bolts and No. 1 viscous heater bracket sub-assembly.


7. REMOVE NO. 2 IDLE PULLEY ASSEMBLY

8. REMOVE GENERATOR ASSEMBLY

A111821
  1. Remove the nut and generator wire.

  1. Disconnect the generator connector.

  1. Remove the 2 bolts and generator.


9. REMOVE GENERATOR BRACKET
  1. Remove the bolt and generator bracket.


10. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A098937E01
    Remove the 4 bolts and V-ribbed belt tensioner assembly.


11. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET
  1. Remove the 4 bolts and No. 1 compressor mounting bracket.


12. REMOVE MANIFOLD STAY WITH VACUUM SWITCHING VALVE (w/ Intercooler)

  1. A211857
    Disconnect the vacuum switching valve connector.

  1. A211858
    Disconnect the 3 vacuum transmitting hoses.

  1. A211859
    Remove the 2 bolts and manifold stay with vacuum switching valve.


13. REMOVE MANIFOLD STAY (w/o Intercooler)

  1. A099622E01
    Remove the 2 bolts and manifold stay.


14. REMOVE FUEL INLET PIPE SUB-ASSEMBLY

  1. A098969E11
    Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.
    Text in Illustration 
    *a
    Common Rail Side
    *b
    Fuel Supply Pump Side


15. REMOVE DIESEL THROTTLE BODY ASSEMBLY (w/ Intercooler)

  1. A111790
    Disconnect the 2 connectors.

  1. A111832
    Remove the 2 bolts, 2 nuts, diesel throttle body assembly and gasket.


16. REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
  1. After removing the fuel pipe, cover the outlets on the common rail with tape to keep out foreign matter.
  2. After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.

  1. w/ Intercooler:

    1. A211871
      Remove the 2 nuts and No. 3 injection pipe clamp.

    2. A211872
      Remove the 2 bolts and 2 No. 2 injection pipe clamps.

    3. A272112E01
      Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
      Text in Illustration 
      *a
      Injector Side
      *b
      Common Rail Side

  1. w/o Intercooler:

    1. A231803E02
      Remove the bolt and No. 2 injection pipe clamp.
      Text in Illustration 
      *1
      No. 2 Injection Pipe Clamp
      *2
      No. 3 Injection Pipe Clamp
      *a
      Injector Side
      *b
      Common Rail Side

    2. Remove the 2 nuts and No. 3 injection pipe clamp.

    3. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.


17. REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET (w/ Intercooler)

  1. A273018E01
    Remove the 3 bolts and No. 2 intake air connector bracket.
    Text in Illustration 
    *A
    w/ Intercooler
    *B
    w/o Intercooler
    *1
    No. 2 Intake Air Connector Bracket
    *2
    Intake Air Connector


18. DISCONNECT NO. 3 WATER BY-PASS PIPE (w/ Intercooler)

  1. A147216
    Remove the 2 bolts and disconnect the No. 3 water by-pass pipe with the wire harness.


19. REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (w/ Intercooler)

  1. w/ Intercooler:

    1. A211846
      Disconnect the 2 connectors.

    2. A252294
      Disconnect the 6 vacuum hoses.

    3. Remove the bolt and No. 1 gas filter with gas filter bracket.

    4. A211848
      Remove the 2 bolts and electric vacuum regulating valve.

  1. w/o Intercooler:

    1. A212373
      Disconnect the connector.

    2. Disconnect the 2 vacuum hoses.

    3. Remove the 2 bolts and electric vacuum regulating valve together with the bracket.

      NOTICE:
      Do not remove the electric vacuum regulating valve from the bracket.


20. REMOVE NO. 2 INTAKE AIR CONNECTOR (w/ Intercooler)

  1. A147230
    Remove the 3 nuts, No. 2 intake air connector and gasket.


21. REMOVE INTAKE AIR CONNECTOR (w/ Intercooler)

  1. A147219
    Remove the 3 bolts, intake air connector and 2 gaskets.


22. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 1 EGR PIPE SUB-ASSEMBLY (w/ Intercooler)

  1. A211879
    Remove the 2 nuts, electric EGR control valve with No. 1 EGR pipe and gasket.


23. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
If an injection pipe clamp is removed from the No. 4 injection pipe, replace the injection clamp with a new one.

  1. w/ Intercooler:

    1. A152275
      Remove the bolt and disconnect the injection pipe clamp.

    2. A152276E07
      Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
      Text in Illustration 
      *a
      Injector Side
      *b
      Common Rail Side

  1. w/o Intercooler:

    1. A098893E01
      Remove the 2 bolts and disconnect the 2 injection pipe clamps.

    2. A231804E02
      Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
      Text in Illustration 
      *a
      Injector Side
      *b
      Common Rail Side


24. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
  1. Disconnect the 3 fuel hoses.

  1. A271807E01
    w/ Intercooler:
    Remove the union bolt, 3 bolts, No. 2 nozzle leakage pipe and gasket.
    Text in Illustration 
    *1
    Union Bolt

  1. A272915E01
    w/o Intercooler:
    Remove the union bolt, 2 bolts, No. 2 nozzle leakage pipe and gasket.
    Text in Illustration 
    *1
    Union Bolt


25. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

NOTICE:
If the cylinder head cover is removed, replace the 4 No. 3 cylinder head cover gaskets with new ones.

  1. Remove the 3 bolts and disconnect the 4 injector connectors.

  1. A060180E01
    Using a small screwdriver, remove the nozzle holder seal by prying between the nozzle holder seal and the cutout part of the cylinder head cover.

  1. Disconnect the ventilation hose.

  1. G034877E01
    Remove the 10 bolts, 2 nuts, cylinder head cover and cylinder head cover gasket.

  1. A289511
    Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover.


26. REMOVE CAMSHAFT TIMING PULLEY

  1. A060182E01
    Remove the bolt of the camshaft timing pulley while holding the camshaft with a wrench.

    NOTICE:
    Make sure the timing belt is not installed when removing the bolt of the camshaft timing pulley.

  1. Remove the camshaft timing pulley.


27. REMOVE NO. 2 TIMING BELT COVER
  1. Remove the 4 bolts, nut and No. 2 timing belt cover.


28. REMOVE ENGINE WATER PUMP ASSEMBLY

A225339
  1. Remove the 5 bolts, 2 nuts, water pump and gasket.


29. REMOVE VACUUM PUMP ASSEMBLY

  1. A098930E01
    Remove the 2 nuts, vacuum pump assembly and 2 O-rings.


30. REMOVE VANE PUMP ASSEMBLY

  1. A233594
    Remove the 2 nuts, vane pump assembly and O-ring.


31. REMOVE PUMP DRIVE SHAFT PULLEY

  1. A038747E01
    Remove the 4 bolts, No. 2 camshaft timing pulley flange and pump drive shaft pulley.

  1. A070711E03
    Using SST, hold the crankshaft pulley and remove the nut and O-ring.
    SST
    09213-58014  
    09330-00021  


32. REMOVE CRANKSHAFT PULLEY

  1. A072413E02
    Using SST, remove the pulley bolt.
    SST
    09213-58014  
    09330-00021  

  1. A072414E02
    Using SST, remove the crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply oil or grease to the threads and tip of SST (center bolt) before using it.


33. REMOVE CAMSHAFT POSITION SENSOR
  1. Remove the bolt and camshaft position sensor.


34. REMOVE CRANKSHAFT POSITION SENSOR
  1. Remove the bolt and crankshaft position sensor.


35. REMOVE TIMING GEAR COVER

  1. A038748E01
    Remove the wire harness clamp.

  1. Remove the 14 bolts and 2 nuts.

  1. Using a slotted screwdriver, gently separate the cover from the timing gear case.

    HINT:
    There are tiny slots that allow you to insert the slotted screwdriver tip for separating the timing gear case and its cover. Refer to the illustration for the slot locations.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing gear case and its cover.

  1. Remove the cover and O-ring.


36. REMOVE NO. 1 IDLE GEAR

  1. A060161E09
    Secure the No. 2 idle sub gear to the No. 1 idle gear with a service bolt.
    Text in Illustration 
    *1
    Service Bolt

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    If the bolt hole of the No. 2 idle sub gear is not aligned with the bolt hole of the No. 1 idle gear, rotate the crankshaft counterclockwise to align the bolt holes. Then install the service bolt.

  1. Remove the 2 bolts and thrust plate.

  1. Remove the service bolt.

  1. Turn the No. 2 idle sub gear and align the gear teeth of the No. 1 idle gear and No. 2 idle sub gear.

  1. Remove the No. 1 idle gear together with the No. 2 idle sub gear.

  1. Remove the idle gear shaft.


37. REMOVE CRANKSHAFT TIMING GEAR

  1. A060163E01
    Remove the No. 1 crankshaft sensor plate.

  1. A060156E01
    Using SST, remove the crankshaft timing gear.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05010)


38. REMOVE INJECTION GEAR

  1. A071164E01
    Using SST, remove the injection gear.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)


39. REMOVE FUEL SUPPLY PUMP ASSEMBLY

G036615E01
  1. Remove the bolt and clamp.

  1. Remove the 2 bolts and oil level gauge guide.

  1. A098969E07
    Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.

  1. A098895E01
    Disconnect the 2 fuel hoses.

  1. A098896E01
    Disconnect the 2 connectors.

  1. A070710E01
    Remove the 4 bolts indicated by the arrows in the illustration.

  1. Remove the No. 2 camshaft timing pulley flange and pump drive shaft pulley.

  1. A070711E02
    Remove the set nut and O-ring while holding the crankshaft pulley by using SST.
    SST
    09213-58013  
    09330-00021  

  1. A098897E01
    Loosen the 2 nuts.

  1. A070714E01
    Using SST, disconnect the pump from the injection gear.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply lubricant to the threads and tip of SST (center bolt) before using it.

  1. Remove the 2 nuts and pump.

    NOTICE:
    1. Do not hold the pump or carry it holding the pipe.
    2. The pump must be kept horizontal.

  1. Remove the O-ring.


40. REMOVE ENGINE OIL LEVEL DIPSTICK

41. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Remove the bolt and dipstick guide.

  1. Remove the O-ring from the dipstick guide.


42. REMOVE OIL PAN SUB-ASSEMBLY
  1. Remove the 22 bolts and 2 nuts.

  1. Z004119E03
    Insert the blade of an oil pan seal cutter between the cylinder block and oil pan. Cut through the applied sealer and remove the oil pan.

    NOTICE:
    1. Do not use the oil pan seal cutter for the timing gear case and rear oil seal retainer.
    2. Be careful not to damage the oil pan flange.

  1. Clean off any sealer remaining on the oil pan and cylinder block.


43. REMOVE OIL STRAINER SUB-ASSEMBLY
  1. Remove the 2 bolts, nut, oil strainer and gasket.


44. REMOVE TIMING GEAR CASE ASSEMBLY
  1. Remove the nut and No. 1 vacuum transmitting pipe.

  1. A060153E01
    Remove the 8 bolts and union bolt. Then remove the timing gear case and 2 O-rings.

    NOTICE:
    Do not drop the oil pump rotor.

  1. Remove the gasket.

← REMOVAL (Aug 2012 – Jul 2013)DISASSEMBLY (from Jun 2011) →