2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Aug 2013

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

NOTICE:
  1. When replacing the injector assemblies (including shuffling the injector assemblies between the cylinders), common rail assembly or cylinder head sub-assembly, it is necessary to replace the injection pipe sub-assemblies with new ones.
  2. When replacing the fuel supply pump assembly, common rail assembly, cylinder block sub-assembly, cylinder head sub-assembly, cylinder head gasket or timing gear case assembly, it is necessary to replace the fuel inlet pipe sub-assembly with a new one.
  3. After removing the injection pipe sub-assemblies, clean them with a brush and compressed air.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag activation.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE HOOD SUB-ASSEMBLY
  1. Disconnect the washer nozzle hose.

  1. Remove the 4 bolts and hood sub-assembly.


3. REMOVE NO. 1 ENGINE UNDER COVER (for 4WD and Pre-Runner)

4. REMOVE NO. 2 ENGINE UNDER COVER (for 4WD and Pre-Runner)

5. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug, and drain the engine oil from the oil pan.

    NOTICE:
    Collect the oil in an oil disposal container.


6. DRAIN MANUAL TRANSMISSION OIL (for Manual Transmission)

7. DRAIN AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)

8. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. A099591E01
    Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.

  1. Loosen the cylinder block drain cock plug.

    A147246E01


9. DRAIN POWER STEERING FLUID

10. REMOVE BATTERY BRACKET

11. REMOVE BATTERY AND BATTERY TRAY

12. REMOVE AIR CLEANER ASSEMBLY
  1. w/o EGR Cooler:
    Disconnect the ventilation hose.

  1. w/ Mass Air Flow Meter:
    Disconnect the mass air flow meter sensor connector.

  1. w/ Intake Air Temperature Sensor:
    Disconnect the intake air temperature sensor connector.

  1. Loosen the hose clamp.

  1. Remove the 2 bolts and air cleaner assembly.


13. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

  1. A135916
    Remove the 3 bolts, 2 nut and engine cover.


14. REMOVE INTERCOOLER ASSEMBLY WITH INTAKE AIR CONNECTOR (w/ Intercooler)

  1. A149802
    Detach the 2 clamps.

  1. Disconnect the vacuum hose from the manifold absolute pressure sensor.

  1. Disconnect the IAT sensor connector and manifold absolute diesel pressure sensor connector.

  1. A149933
    Loosen the 2 hose clamps of the No. 1 air hose.

  1. A149934
    Loosen the 2 hose clamps of the No. 2 air hose.

  1. A135919
    Remove the 4 bolts and intercooler.


15. REMOVE NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY (w/o Intercooler)

  1. w/ No. 1 Engine Cover

    1. A099256E03
      Detach the 4 claws from the pins of the engine cover bracket and remove the No. 1 engine cover sub-assembly.
      Text in Illustration 
      *1
      No. 1 Engine Cover Sub-assembly
      *2
      Claw
      *3
      Pin

    2. Remove the 2 bolts and engine cover bracket.

  1. A111789
    Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the vacuum hose from the gas filter.

  1. Loosen the 2 clamps.

  1. Remove the bolt and disconnect the No. 2 air cleaner pipe sub-assembly together with the 2 air hoses.


16. REMOVE STARTER ASSEMBLY
  1. for 2.0 kW Type: (Click here)
  2. for 2.2 kW Type: (Click here)
  3. for 2.7 kW Type: (Click here)

17. REMOVE FRONT EXHAUST PIPE ASSEMBLY
(Click here)

18. REMOVE FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)

C098708E01
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts, 4 bolts and 4 washers, and disconnect the propeller shaft.

  1. F052086E01
    Place matchmarks on the propeller shaft flange and transfer flange.

  1. Remove the 4 nuts, 4 washers and front propeller shaft.


19. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
(Click here)

20. REMOVE RADIATOR ASSEMBLY
(Click here)

21. DISCONNECT HEATER HOSE

  1. A236415
    Slide the 2 clamps and disconnect the 2 heater hoses from the water outlet and heater pipe.


22. DISCONNECT PRESSURE FEED TUBE ASSEMBLY

  1. A236416
    Slide the clamp and disconnect the oil reservoir to pump hose from the vane pump assembly.

  1. A236417
    Disconnect the pressure feed tube assembly from the vane pump assembly.


23. DISCONNECT FUEL HOSE

  1. A236418
    Slide the 2 clamps and disconnect the 2 fuel hoses from the No. 2 nozzle leakage pipe assembly and fuel supply pump assembly.


24. DISCONNECT UNION TO CONNECTOR TUBE HOSE

  1. A236419
    Slide the clamps and disconnect the union to connector tube hose from the No. 1 hose to hose tube.


25. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

B278058E01
  1. Slightly bend the upper part of the glove compartment door to release the 2 stoppers and open the glove compartment door until it is horizontal.

    Text in Illustration 
    *1
    Stopper

  1. B278059E01
    Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.
    Text in Illustration 
    *1
    Hinge


26. DISCONNECT WIRE HARNESS

A236420
  1. Remove the upper relay block cover.

  1. Remove the side relay block cover.

  1. Remove the nut and disconnect the engine room junction block wire.

  1. Disconnect the 2 engine room junction block connectors.

  1. Remove the bolt and disconnect the ground cable.

  1. A233020
    Remove the 2 nuts, detach the clamp and disconnect the wire harness.

  1. A238474E02
    Disconnect the 3 EDU connectors.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

  1. A272289E01
    for Variable Nozzle Vane Turbocharger:
    Disconnect the turbo motor driver connector.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD

  1. w/ A.D.D.:
    Disconnect the 4WD control ECU connector.

  1. for Automatic Transmission:
    Disconnect the 3 TCM connectors.

  1. Disconnect the 4 ECM connectors.


27. DISCONNECT COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)
  1. Remove the 4 bolts and disconnect the cooler compressor assembly.

    HINT:
    It is not necessary to completely remove the compressor assembly. With the hoses connected to the compressor assembly, hang the compressor assembly on the vehicle body with a rope.


28. REMOVE MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)
  1. for R151/R156: (Click here)
  2. for R151F/R156F: (Click here)
  3. for G50: (Click here)

29. REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT

30. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
(Click here)

31. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)

  1. D029616E01
    Place matchmarks on the clutch cover and flywheel.

  1. Loosen each set bolt one turn at a time until spring tension is released.

  1. Remove the 6 set bolts and pull off the clutch cover.

    NOTICE:
    Do not drop the clutch disc.


32. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

NOTICE:
Keep the lining part of the clutch disc, pressure plate and surface of the flywheel away from oil and foreign matter.


33. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

  1. A072851E02
    Using SST, hold the crankshaft pulley.
    SST
    09213-58014  
    09330-00021  

  1. A114803
    Remove the 8 bolts and flywheel sub-assembly.


34. REMOVE PUMP IMPELLER DRIVE PLATE (for Automatic Transmission)

  1. A072851E02
    Using SST, hold the crankshaft pulley.
    SST
    09213-58014  
    09330-00021  

  1. A114804
    Remove the 8 bolts, the rear drive plate spacer, the pump impeller drive plate, and the flywheel sub-assembly.


35. REMOVE REAR END PLATE
  1. Remove the bolt and rear end plate.


36. INSTALL ENGINE HANGERS

  1. A224109E01
    Install a No. 1 engine hanger and No. 2 engine hanger with 2 bolts as shown in the illustration.

    Torque:
    for No. 1 engine hanger:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }
    for No. 2 engine hanger:
    60 N*m{ 612 kgf*cm , 44 ft.*lbf }

    Text in Illustration 
    *1
    No. 1 Engine Hanger
    *2
    No. 2 Engine Hanger

    HINT:
    Part No.
    No. 1 engine hanger
    w/ Intercooler
    12284-30060
    w/o Intercooler
    12284-30020
    No. 2 engine hanger
    12282-67030
    Bolt
    90105-T0164 or 91552-81014 and 90119-T0065 or 91642-81030

    NOTICE:
    Install the engine hangers with new bolts.


37. REMOVE ENGINE ASSEMBLY
  1. Attach an engine sling device and hang the engine assembly with a chain block.

  1. A148168
    w/ EGR Cooler:
    Remove the bolt and No. 2 cylinder block insulator.

  1. A098988E01
    Remove the 4 bolts and 4 nuts.

  1. Remove the engine assembly by operating the engine sling device and chain block.


38. FIX ENGINE ON ENGINE STAND
  1. Install the engine assembly to an engine stand with the bolts.

  1. Remove the 2 bolts and 2 engine hangers.


39. REMOVE ENGINE WIRE
  1. Remove the engine wire.


40. REMOVE NO. 1 TIMING BELT COVER
  1. Remove the bolt and water hose clamp.

  1. Remove the wire harness clamp.

  1. A148169
    Remove the 6 bolts and timing belt cover.


41. REMOVE TIMING BELT

  1. A070549E02
    Turn the crankshaft clockwise and align the timing marks as shown in the illustration.

  1. A070550E01
    Uniformly loosen the 2 bolts and remove the timing belt tensioner.

  1. Remove the timing belt.

  1. Using a 10 mm hexagon wrench, remove the bolt, timing belt idler and washer.

    HINT:
    A148170E01
    1. When turning the camshaft while the timing belt is removed, turn the crankshaft 90° counterclockwise.
    2. When installing the timing belt, return the camshaft to the timing marks and then turn the crankshaft clockwise until it aligns with the timing marks, as shown in the illustration.


42. REMOVE CRANKSHAFT PULLEY

  1. A072413E02
    Using SST, remove the pulley bolt.
    SST
    09213-58014  
    09330-00021  

  1. A072414E02
    Using SST, remove the crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply oil or grease to the threads and tip of SST (center bolt) before using it.


43. REMOVE TURBOCHARGER SUB-ASSEMBLY (w/ EGR Cooler)
(Click here)

44. REMOVE TURBOCHARGER SUB-ASSEMBLY (w/o EGR Cooler)
(Click here)

45. REMOVE EXHAUST MANIFOLD

  1. A149962E02
    w/ Intercooler:
    Remove the 8 nuts, 8 spacers, 8 collars and exhaust manifold.
    Text in Illustration 
    *A
    w/ Intercooler
    *B
    w/o Intercooler

  1. w/o Intercooler:
    Remove the 8 nuts, 8 spacers and exhaust manifold.


46. INSPECT EXHAUST MANIFOLD

  1. A098949E01
    Using a precision straightedge and feeler gauge, measure the surface contacting the cylinder head sub-assembly for warpage.

    Maximum warpage:
    0.40 mm (0.0157 in.)

    If the warpage is more than the maximum, replace the exhaust manifold.


47. REMOVE GENERATOR ASSEMBLY

A111821
  1. Remove the nut and generator wire.

  1. Disconnect the generator connector.

  1. Remove the 2 bolts and generator.


48. REMOVE GENERATOR BRACKET
  1. Remove the bolt and generator bracket.


49. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

  1. A098937E01
    Remove the 4 bolts and V-ribbed belt tensioner assembly.


50. REMOVE INTERCOOLER SUPPORT BRACKET (w/ Intercooler)
  1. Remove the 2 bolts and intercooler support bracket.


51. REMOVE NO. 2 INTERCOOLER SUPPORT BRACKET (w/ Intercooler)
  1. Remove the 2 bolts and No. 2 intercooler support bracket.


52. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)
  1. Remove the 4 bolts and No. 1 compressor mounting bracket.


53. REMOVE VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY (w/ Viscous Heater)

  1. I034100E02
    Disconnect the connector.

  1. Remove the 2 bolts and viscous with magnet clutch heater assembly.


54. REMOVE NO. 1 VISCOUS HEATER BRACKET SUB-ASSEMBLY (w/ Viscous Heater)
  1. Remove the 4 bolts and No. 1 viscous heater bracket sub-assembly.


55. REMOVE WATER INLET

A097637E01
  1. Remove the 3 bolts and water inlet.


56. REMOVE THERMOSTAT
  1. Remove the thermostat from the cylinder block.

  1. Remove the gasket from the thermostat.


57. REMOVE WATER OUTLET

  1. A149947E02
    Remove the 2 bolts and water outlet.
    Text in Illustration 
    *A
    w/ EGR Cooler:
    *B
    w/o EGR Cooler:


58. REMOVE GLOW PLUG ASSEMBLY
  1. w/ EGR Cooler: (Click here)
  2. w/ EGR System without EGR Cooler: (Click here)
  3. w/o EGR System: (Click here)

59. REMOVE INTAKE MANIFOLD
(Click here)

60. INSPECT INTAKE MANIFOLD

  1. A098945E01
    Using a precision straightedge and feeler gauge, measure the surface contacting the cylinder head sub-assembly for warpage.

    Maximum warpage:
    0.40 mm (0.0157 in.)

    If the warpage is more than the maximum, replace the intake manifold.


61. REMOVE NO. 2 EGR HOLE COVER PLATE (w/o EGR System)
  1. Remove the 2 nuts and No. 2 EGR hole cover plate.

  1. Remove the gasket.


62. REMOVE OIL FILTER SUB-ASSEMBLY

A147257E01
  1. Using SST, remove the oil filter.

    SST
    09228-07501  

    HINT:
    Insert the drain hose in the oil cooler cover. Put the disposal container beneath the drain hose to collect the oil from the oil cooler cover.


63. REMOVE FUEL INLET PIPE SUB-ASSEMBLY

  1. A152281
    Remove the bolt and clamp.

  1. A153562
    Remove the bolt and oil level gauge guide.

  1. A152282E03
    Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.


64. REMOVE FUEL SUPPLY PUMP ASSEMBLY

G036615E01
  1. Remove the bolt and clamp.

  1. Remove the 2 bolts and oil level gauge guide.

  1. A098969E07
    Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.

  1. A098895E01
    Disconnect the 2 fuel hoses.

  1. A098896E01
    Disconnect the 2 connectors.

  1. A070710E01
    Remove the 4 bolts indicated by the arrows in the illustration.

  1. Remove the No. 2 camshaft timing pulley flange and pump drive shaft pulley.

  1. A070711E02
    Remove the set nut and O-ring while holding the crankshaft pulley by using SST.
    SST
    09213-58013  
    09330-00021  

  1. A098897E01
    Loosen the 2 nuts.

  1. A070714E01
    Using SST, disconnect the pump from the injection gear.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply lubricant to the threads and tip of SST (center bolt) before using it.

  1. Remove the 2 nuts and pump.

    NOTICE:
    1. Do not hold the pump or carry it holding the pipe.
    2. The pump must be kept horizontal.

  1. Remove the O-ring.


65. REMOVE COMMON RAIL ASSEMBLY
  1. Disconnect the 2 connectors.

  1. A231856
    Remove the 2 bolts, common rail and No. 2 intake manifold insulator.

    NOTICE:
    Do not remove the pressure discharge valve or fuel pressure sensor.


66. REMOVE OIL COOLER COVER SUB-ASSEMBLY
  1. Disconnect the oil pressure switch connector.

  1. Remove the 2 nuts and disconnect the No. 2 vacuum transmitting pipe from the oil cooler cover.

  1. A038741E01
    Remove the 13 bolts, oil cooler cover and gasket.


67. REMOVE TIMING GEAR COVER INSULATOR (w/ EGR Cooler)

  1. A148171
    Remove the bolt and timing gear cover insulator.


68. REMOVE VACUUM PUMP ASSEMBLY

  1. A098930E01
    Remove the 2 nuts, vacuum pump assembly and 2 O-rings.


69. REMOVE VANE PUMP ASSEMBLY

  1. A233594
    Remove the 2 nuts, vane pump assembly and O-ring.


70. REMOVE CRANKSHAFT POSITION SENSOR
  1. Remove the bolt and crankshaft position sensor.


71. REMOVE CAMSHAFT POSITION SENSOR
  1. Remove the bolt and camshaft position sensor.


72. REMOVE ENGINE COOLANT TEMPERATURE SENSOR
  1. Using a 19 mm deep socket wrench, remove the engine coolant temperature sensor and gasket.


73. REMOVE FRONT ENGINE MOUNTING INSULATOR

  1. A233592E03
    Remove the 2 nuts and 2 front engine mounting insulators.
    Text in Illustration 
    *a
    RH Side:
    *b
    LH Side:


74. REMOVE NO. 1 FRONT ENGINE MOUNTING BRACKET RH

  1. A233593E03
    Remove the 4 bolts and No. 1 front engine mounting bracket RH.
    Text in Illustration 
    *a
    RH Side:
    *b
    LH Side:


75. REMOVE NO. 1 FRONT ENGINE MOUNTING BRACKET LH
  1. Remove the 4 bolts and No. 1 front engine mounting bracket LH.

← REMOVAL (Aug 2012 – Jul 2013)INSTALLATION (Jun 2011 – Jul 2012) →