INSTALLATION
Removal / installation · Vehicles built from Aug 2013
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
| 1.
INSTALL GENERATOR ASSEMBLY |
 |
- Install the generator with the bolt.
-
Torque:
- 75 N*m{
765 kgf*cm
, 55 ft.*lbf
}
Connect the vacuum oil outlet hose.
- Install 2 new gaskets and the vacuum pump hose with the union bolt.
-
Torque:
- 14 N*m{
143 kgf*cm
, 10 ft.*lbf
}
Install the vacuum pump oil inlet hose with 2 new gaskets and the union bolt.
-
Torque:
- 14 N*m{
143 kgf*cm
, 10 ft.*lbf
}
Attach the vacuum pump oil inlet hose to the cord clip.
- Install the generator wire with the nut.
-
Torque:
- 9.8 N*m{
100 kgf*cm
, 7 ft.*lbf
}
Attach the terminal cap.
Connect the generator connector.
| 2.
INSTALL COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System) |
 |
- Temporarily install the compressor mounting bracket with the 4 bolts.
Using several steps, uniformly install and tighten the 4 bolts in the sequence shown in the illustration.
-
Torque:
- 85 N*m{
865 kgf*cm
, 63 ft.*lbf
}
- Temporarily tighten the bolt and spacer.
-
Torque:
- 18 N*m{
184 kgf*cm
, 13 ft.*lbf
}
| 3.
INSTALL COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System) |
 |
- Install the compressor with the 4 bolts.
-
Torque:
- 25 N*m{
255 kgf*cm
, 18 ft.*lbf
}
Connect the compressor connector.
| 4.
INSTALL FAN BELT ADJUSTING BAR (w/o Air Conditioning System) |
 |
- Install the fan belt adjusting bar with the 2 bolts.
-
Torque:
- 45 N*m{
460 kgf*cm
, 33 ft.*lbf
}
- Temporarily install the bolt.
| 5.
INSTALL FAN & GENERATOR V BELT (w/o Air Conditioning System)
|
 |
- Install the V belt.
Using a bar, adjust the tension of the V belt.
Tighten the bolts A and B.
-
Torque:
- Bolt A:
- 75 N*m{
765 kgf*cm
, 55 ft.*lbf
}
- Bolt B:
- 18 N*m{
185 kgf*cm
, 13 ft.*lbf
}
Check the deflection of the V belt (Click here).
| 6.
INSTALL FAN AND GENERATOR V BELT (w/ Air Conditioning System)
|
 |
Rotate the V-ribbed belt tensioner pulley clockwise, and then install the fan and generator V belt.
- NOTICE:
- Make sure that the fan and generator V belt is set properly on each pulley.
Check that the indicator mark of the V-ribbed belt tensioner (Click here).
| 7.
INSTALL COOLER COMPRESSOR V BELT (w/ Air Conditioning System)
|
 |
- Install the V belt.
Tightening the bolt B, adjust the tension of the V belt.
Tighten nut A.
-
Torque:
- 39 N*m{
400 kgf*cm
, 29 ft.*lbf
}
Check the tension of the V belt (Click here).
| 8.
INSTALL AIR CLEANER ASSEMBLY |
 |
- Install the cleaner with the 2 bolts.
-
Torque:
- 14 N*m{
143 kgf*cm
, 10 ft.*lbf
}
Connect the connector to the IAT sensor.
Connect the hose clamp.
| 9.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
|
| 10.
PERFORM INITIALIZATION |
 |
Perform initialization (Click here).
- NOTICE:
- Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.