2014 Hilux · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013


1. INSTALL GENERATOR ASSEMBLY

  1. A122287
    Install the generator with the bolt.

    Torque:
    75 N*m{ 765 kgf*cm , 55 ft.*lbf }

  1. Connect the vacuum oil outlet hose.

  1. A118425
    Install 2 new gaskets and the vacuum pump hose with the union bolt.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

  1. Install the vacuum pump oil inlet hose with 2 new gaskets and the union bolt.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

  1. Attach the vacuum pump oil inlet hose to the cord clip.

  1. A118424
    Install the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 7 ft.*lbf }

  1. Attach the terminal cap.

  1. Connect the generator connector.


2. INSTALL COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)

  1. A121135E02
    Temporarily install the compressor mounting bracket with the 4 bolts.

  1. Using several steps, uniformly install and tighten the 4 bolts in the sequence shown in the illustration.

    Torque:
    85 N*m{ 865 kgf*cm , 63 ft.*lbf }

  1. A112016E01
    Temporarily tighten the bolt and spacer.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


3. INSTALL COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

  1. A118422
    Install the compressor with the 4 bolts.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

  1. Connect the compressor connector.


4. INSTALL FAN BELT ADJUSTING BAR (w/o Air Conditioning System)

  1. A123775
    Install the fan belt adjusting bar with the 2 bolts.

    Torque:
    45 N*m{ 460 kgf*cm , 33 ft.*lbf }

  1. A123774
    Temporarily install the bolt.


5. INSTALL FAN & GENERATOR V BELT (w/o Air Conditioning System)

  1. A115631E01
    Install the V belt.

  1. Using a bar, adjust the tension of the V belt.

  1. Tighten the bolts A and B.

    Torque:
    Bolt A:
    75 N*m{ 765 kgf*cm , 55 ft.*lbf }
    Bolt B:
    18 N*m{ 185 kgf*cm , 13 ft.*lbf }

  1. Check the deflection of the V belt (Click here).


6. INSTALL FAN AND GENERATOR V BELT (w/ Air Conditioning System)
  1. Rotate the V-ribbed belt tensioner pulley clockwise, and then install the fan and generator V belt.

    NOTICE:
    Make sure that the fan and generator V belt is set properly on each pulley.

  1. Check that the indicator mark of the V-ribbed belt tensioner (Click here).


7. INSTALL COOLER COMPRESSOR V BELT (w/ Air Conditioning System)

  1. A121093E02
    Install the V belt.

  1. Tightening the bolt B, adjust the tension of the V belt.

  1. Tighten nut A.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }

  1. Check the tension of the V belt (Click here).


8. INSTALL AIR CLEANER ASSEMBLY

  1. A118427
    Install the cleaner with the 2 bolts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

  1. Connect the connector to the IAT sensor.

  1. Connect the hose clamp.


9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

10. PERFORM INITIALIZATION
  1. Perform initialization (Click here).

    NOTICE:
    Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.

← REASSEMBLY (from Jun 2011)INSTALLATION (Aug 2012 – Jul 2013) →