2014 Hilux · Service Manual ENGINE

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Jun 2011


INSPECT INJECTION TIMING

  1. A073717E01
    Using a mirror, check that the matchmarks of the injection pump flange and the timing gear case are aligned.


ADJUST INJECTION TIMING

  1. A073718E01
    Loosen the following nuts and bolts.

    1. Bolt holding the injection pump to the injection pump stay.

    2. 2 nuts holding the injection pump to the timing gear case.

  1. Align the matchmark by slightly tilting the injection pump.

  1. Tighten the following nuts and bolts.

    1. 2 nuts holding the injection pump to the timing gear case.

      Torque:
      21 N*m{ 210 kgf*cm , 15 ft.*lbf }

    2. Bolt holding the injection pump to the injection pump stay.

      Torque:
      26 N*m{ 270 kgf*cm , 19 ft.*lbf }


INSPECT ENGINE IDLE SPEED
  1. Warm up the engine.

  1. When using the intelligent tester:

    1. Connect the intelligent tester to the DLC3.

    2. Measure the idle speed.

      Standard idle speed:
      720 to 820 rpm (A/C OFF)
      750 to 850 rpm (A/C ON)

      HINT:
      Refer to the intelligent tester operator's manual for further details.

  1. A082779E58
    When not using the intelligent tester:

    1. Using SST, connect the tachometer test probe to terminal 9 (TAC) of the DLC3.

      SST
      09843-18040  

    2. Measure the idle speed.

      Standard idle speed:
      720 to 820 rpm (A/C OFF)
      750 to 850 rpm (A/C ON)

      NOTICE:
      Switch off all accessories.


INSPECT MAXIMUM SPEED
  1. Start the engine.

  1. Fully depress the accelerator pedal.

  1. Measure the maximum speed.

    Maximum speed:
    4,850 to 4,950 rpm


INSPECT COMPRESSION

HINT:
If there is a lack of power, excessive oil consumption or poor fuel economy is suspected. Measure the compression pressure.

  1. Warm up and stop the engine.

  1. Remove the glow plugs (Click here).

  1. Disconnect the spill control valve connector.

  1. Check the cylinder compression pressure.

    HINT:
    Turn the starter before measuring the compression pressure and remove the foreign objects.


    1. A073719E01
      Install SST (attachment) to the glow plug hole.
      SST
      09992-00025   (09992-00121)

      Torque:
      13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    2. A073720E01
      Connect SST (compression gauge) to the SST (attachment).
      SST
      09992-00025   (09992-00211)

    3. Fully open the throttle valve, and start the engine.

    4. While cranking the engine, measure the compression pressure.

      HINT:
      Always use a fully charged battery to obtain engine revolution of 250 rpm or more.

  1. Perform the step above for each cylinder.

    NOTICE:
    This measurement must be done as quickly as possible.

    Standard compression pressure:
    3,138 kPa (32.0 kgf/cm2, 455 psi) or more

    Minimum pressure:
    1,961 kPa (20.0 kgf/cm2, 284 psi)

    Difference between each cylinder:
    490 kPa (5.0 kgf/cm2, 71 psi) or less

    If the cylinder compression in one or more cylinders is low, pour a small amount of engine oil into the cylinder through the glow plug hole. Then, repeat the step above for the cylinder with low compression.

    HINT:
    1. If adding oil helps the compression, the piston rings and/or cylinder bore may be worn or damaged.
    2. If pressure stays low, a valve may be stuck or the seating may be improper, or there may be leakage past the gasket.

  1. Remove the SST.

  1. Reinstall the glow plugs (Click here).

  1. Reconnect the spill control valve connector.

← REPAIR (from Jun 2011)COMPONENTS (from Jun 2011) →