REASSEMBLY
Removal / installation · Vehicles built from Jun 2011
| 1. INSTALL INSTALL VANE PUMP HOUSING OIL SEAL |
![]() ![]() |
Using SST and a press, press in a new oil seal.
- SST
- 09950-60010
09950-70010 (09951-00280, 09951-07100)
- NOTICE:
- Make sure to install the oil seal facing the correct direction.
- Be careful not to damage the oil seal.
- Make sure to install the oil seal facing the correct direction.
| 2. INSTALL SHAFT WITH PULLEY |
![]() ![]() |
Coat the shaft with power steering fluid.
Tape the serrated part of the shaft.
- NOTICE:
- Be careful not to damage the oil seal.
| 3. INSTALL FRONT VANE PUMP SIDE PLATE |
![]() ![]() |
Coat a new No. 2 O-ring with power steering fluid.
Install the No. 2 O-ring to the front housing.
Coat a new No. 1 O-ring with power steering fluid.

Install the No. 1O-ring to the front side plate.
Install the front side plate to the front housing while aligning the semicircle-shaped cuts of both parts.

- NOTICE:
- Be sure to install the plate in the correct position and direction.
| 4. INSTALL VANE PUMP CAM RING |
![]() ![]() |
With the inscribed mark facing upward, install the vane pump cam ring to the vane pump front housing while aligning the semicircle-shaped cuts of both parts.
- NOTICE:
- Be sure to install the plate in the correct position and direction.
| 5. INSTALL VANE PUMP ROTOR |
![]() ![]() |
Install the vane pump rotor to the front vane pump housing.
- HINT:
- The top and bottom of the vane pump rotor are symmetrical.
Coat the 10 vane pump plates with power steering fluid.

Install the 10 vane pump plates.
- NOTICE:
- Make sure that the round ends of the vane pump plates are facing outward.
| 6. INSTALL VANE PUMP SHAFT SNAP RING |
![]() ![]() |
Using a screwdriver and snap ring expander, install a new snap ring to the shaft with pulley.
| 7. INSTALL REAR VANE PUMP HOUSING |
![]() ![]() |
Coat a new O-ring with power steering fluid and install it onto the rear housing.
Align the straight pin of the rear housing with the hole created by the semicircle-shaped cuts of the cam ring, front side plate and front housing. Then install the rear housing with the 4 bolts.
- Torque:
- 22 N*m{ 224 kgf*cm , 16 ft.*lbf }
- NOTICE:
- Make sure that the O-ring is not out of position before installing the rear vane pump housing.
| 8. INSPECT PRELOAD |
![]() ![]() |
Check that the pump rotates smoothly without abnormal noise.
Temporarily install the service bolt.
- Recommended service bolt:
Item
Length
Thread Diameter
10 mm (0.39 in.)
Thread Pitch
1.25 mm (0.0492 in.)
Bolt Length
50 mm (1.97 in.)
- Rotating torque:
- 0.27 N*m (2.8 kgf*cm, 2.4 in.*lbf) or less
| 9. INSTALL POWER STEERING OIL PRESSURE SWITCH |
Coat a new O-ring with power steering fluid and install it to the oil pressure switch.
Install the oil pressure switch onto the vane pump.
- Torque:
- 21 N*m{ 214 kgf*cm , 15 ft.*lbf }
| 10. INSTALL FLOW CONTROL VALVE |
![]() ![]() |
Coat the compression spring and flow control valve with power steering fluid.
Install the compression spring.
Install the flow control valve facing in the correct direction.
Coat a new O-ring with power steering fluid and install it onto the pressure port union.
Install the pressure port union.
- Torque:
- 69 N*m{ 704 kgf*cm , 51 ft.*lbf }
| 11. INSTALL VANE PUMP OIL RESERVOIR SUB-ASSEMBLY |
Coat a new O-ring with power steering fluid, and install it to the vane pump reservoir.
Install it to the vane pump reservoir to the vane pump with the 3 bolts.
- Torque:
- 9.0 N*m{ 92 kgf*cm , 80 in.*lbf }
| 12. INSTALL PUMP OIL RESERVOIR CAP SUB-ASSEMBLY |









