2014 Hilux · Service Manual STEERING

INSPECTION

Inspection · Vehicles built from Jun 2011


INSPECT VANE PUMP SHAFT AND BUSHING IN FRONT HOUSING

  1. F047395E09
    Using a micrometer, measure the diameter (a) of the shaft with pulley.

  1. Using a caliper gauge, measure the inside diameter (b) of the front vane pump housing.

    NOTICE:
    Do not damage the bushing in the front vane pump housing.

  1. Subtract (a) from (b) to calculate the oil clearance.

    Maximum clearance:
    0.07 mm (0.0028 in.)

    If it is greater than the maximum, replace the shaft with pulley.


INSPECT VANE PUMP ROTOR AND VANE PUMP PLATES CLEARANCE

  1. ZX00285E01
    Using a feeler gauge, measure the clearance between the side face of the vane pump rotor groove and the vane pump plates.

    Maximum clearance:
    0.03 mm (0.0012 in.)

    NOTICE:
    1. If the clearance is more than the maximum, replace the vane pump plates, vane pump rotor and vane pump cam ring.
    2. Refer to the following table to select an appropriate combination of vane pump rotor, vane pump cam ring and vane pump plates.

      Combination of vane pump rotor, vane pump cam ring and vane pump plates:
      for 2WD 
      Vane Pump Rotor Part No.
      Vane Pump Cam Ring Part No.
      Vane Pump Plate Part No.
      44313-06110
      44325-0K010
      44345-06110
      44313-06120
      44325-0K020
      44345-06120
      44313-06130
      44325-0K030
      44345-06130
      44313-06140
      44325-0K040
      44345-06140
      44313-06150
      44325-0K050
      44345-06150
      for 4WD and Pre-Runner 
      Vane Pump Rotor Part No.
      Vane Pump Cam Ring Part No.
      Vane Pump Plate Part No.
      44313-06110
      44325-06160
      44345-06110
      44313-06120
      44325-06170
      44345-06120
      44313-06130
      44325-06180
      44345-06130
      44313-06140
      44325-06190
      44345-06140
      44313-06150
      44325-06200
      44345-06150


INSPECT FLOW CONTROL VALVE

  1. F052069E01
    Check the flow control valve for leakage. Close one of the holes and apply compressed air of 392 to 490 kPa (4 to 5 kgf/cm2, 57 to 71 psi) to the hole on the opposite side. Confirm that the air does not flow out of the end holes.

    NOTICE:
    Make sure to use clean and dry air.

  1. C220817E01
    If there is leakage, replace the flow control valve.

    NOTICE:
    1. Check the mark on the front vane pump housing and replace the flow control valve with one having the same mark as that of the front vane pump housing.
    2. Refer to the following table to select an appropriate combination of front vane pump housing and flow control valve.

      Combination of front vane pump housing and flow control valve:
      for 2WD 
      Front Vane Pump Housing Mark
      Flow Control Valve Mark
      Flow Control Valve Part No.
      A
      A
      44330-0K130
      B
      B
      44330-0K140
      C
      C
      44330-0K150
      D
      D
      44330-0K160
      E
      E
      44330-0K170
      F
      F
      44330-0K180
      for 4WD and Pre-Runner 
      Front Vane Pump Housing Mark
      Flow Control Valve Mark
      Flow Control Valve Part No.
      A
      A
      44330-0K010
      B
      B
      44330-0K020
      C
      C
      44330-0K030
      D
      D
      44330-0K040
      E
      E
      44330-0K050
      F
      F
      44330-0K060

  1. Coat the flow control valve with power steering fluid.

    NOTICE:
    Make sure to use new power steering fluid.

  1. Insert the flow control valve into the flow control valve installation hole of the front vane pump housing, and check that the flow control valve enters smoothly under its own weight.

  1. If the flow control valve does not enter the front vane pump housing smoothly, replace the flow control valve.


INSPECT FLOW CONTROL VALVE COMPRESSION SPRING

  1. R008702E02
    Using a vernier caliper, measure the free length of the flow control valve compression spring.

    Minimum free length:
    29.2 mm (1.150 in.)

    If the length is less than the minimum, replace the flow control valve compression spring.


INSPECT PRESSURE PORT UNION
  1. If the union seat in the pressure port union is severely damaged, replace the pressure port union.

← DISASSEMBLY (from Jun 2011)REASSEMBLY (from Jun 2011) →