2014 Hilux · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built from Aug 2013


INSPECT STARTER ASSEMBLY

CAUTION:
As a large electric current passes through the cable during this inspection, a thick cable must be used. Otherwise, the cable may become hot and cause injury.

NOTICE:
These tests must be performed within 3 to 5 seconds to prevent the coil from burning out.

  1. Mount the starter assembly in a vise between aluminum plates.

  1. Perform a pull-in test.

    1. Detach the wire harness clamp, remove the nut and disconnect the lead wire from terminal C.

    2. A302468E01
      Connect the battery to the starter assembly as shown in the illustration. Check that the clutch pinion gear moves outward.
      Text in Illustration 
      *1
      Terminal C
      *2
      Terminal 50
      V100135
      Moves outward
      If the clutch pinion gear does not move, replace the magnet starter switch assembly.

  1. Perform a holding test.

    1. A302469E01
      Disconnect the negative (-) terminal lead from terminal C with the condition specified in the pull-in test above being maintained. Check that the pinion gear remains out.
      Text in Illustration 
      *1
      Terminal C
      *2
      Terminal 50
      V100135
      Disconnect
      If the clutch pinion gear moves inward, replace the magnet starter switch assembly.

  1. Inspect clutch pinion gear return.

    1. A302470
      Disconnect the negative (-) terminal lead from the starter body. Check that the clutch pinion gear returns inward.
      Text in Illustration 
      V100135
      Disconnect
      V100136
      Returns inward
      If the clutch pinion gear moves inward, replace the magnet starter switch assembly.

  1. Perform an operation test without load.

    1. Attach the wire harness clamp and connect the lead wire to terminal C with the nut.

      Torque:
      5.9 N*m{ 60 kgf*cm , 52 in.*lbf }

    2. A302471E01
      Connect the battery and an ammeter to the starter assembly as shown in the illustration.
      Text in Illustration 
      *1
      Terminal 50
      *2
      Terminal 30

    3. Check that the starter rotates smoothly and steadily while the pinion gear is moving out. Then measure the current.

      Standard current:
      100 A or less at 11.5 V


INSPECT STARTER ARMATURE ASSEMBLY
  1. Check the commutator for dirt and/or burns on the surface.
    If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.
    If necessary, replace the starter armature assembly.

  1. Check the resistance.

    1. G036820E06
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Segment - Segment
      Always
      Below 1 Ω

      Text in Illustration 
      *1
      Segment
      If the result is not as specified, replace the starter armature assembly.

    2. G036821E06
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Segment - Coil core
      Always
      10 kΩ or higher

      Text in Illustration 
      *1
      Coil Core
      *2
      Segment
      If the result is not as specified, replace the starter armature assembly.

  1. Check the commutator circle runout.

    1. P010586
      Place the commutator on V-blocks.

    2. Using a dial indicator, measure the circle runout.

      Maximum runout:
      0.05 mm (0.00197 in.)

  1. P010587E01
    Using a vernier caliper, measure the commutator diameter.

    Standard diameter:
    35.0 mm (1.39 in.)

    Minimum diameter:
    34.0 mm (1.34 in.)

    If the diameter is less than the minimum, replace the starter armature assembly.

  1. ST00040E01
    Measure the undercut depth of the commutator.

    Standard undercut depth:
    0.7 mm (0.0276 in.)

    Minimum undercut depth:
    0.2 mm (0.00787 in.)

    If the undercut depth is less than the minimum, correct it with a hacksaw blade.
    If necessary, replace the starter armature assembly.


INSPECT STARTER YOKE ASSEMBLY

  1. Check the resistance.

    1. G036822E02
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Lead wire - Field coil brush lead
      Always
      Below 1 Ω

      If the result is not as specified, replace the starter yoke assembly.

    2. G036823E01
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Shunt coil terminal - Shunt coil terminal
      20°C (68°F)
      1.5 to 1.9 Ω

      If the result is not as specified, replace the starter yoke assembly.

  1. Check the brush length.

    1. A302475E01
      Using a vernier caliper, measure the brush length.

      Standard length:
      15.0 mm (0.591 in.)

      Minimum length:
      9.0 mm (0.354 in.)

      Text in Illustration 
      *a
      Length
      If the length is less than the minimum, replace the starter yoke assembly.


INSPECT STARTER BRUSH HOLDER ASSEMBLY

  1. Check the resistance.

    1. G036824E02
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Positive (+) brush holder - Negative (-) brush holder
      Always
      10 kΩ or higher

      If the result is not as specified, replace the starter brush holder assembly.

  1. Check the brush spring load.

    1. ST00019
      Take a pull scale reading the instant the brush spring separates from the brush.

      Standard spring load:
      22 to 28 N (2 to 3 kgf, 4.8 to 6.2 lbf)

      Minimum spring load:
      12 N(1 kgf, 2.8 lbf)

      If the spring load is less than the minimum, replace the starter brush holder assembly.

    2. A302474E01
      Using a vernier caliper, measure the brush length

      Standard length:
      15.0 mm (0.591 in.)

      Minimum length:
      9.0 mm (0.354 in.)

      Text in Illustration 
      *a
      Length
      If the length is less than the minimum, replace the starter brush holder assembly.


INSPECT STARTER CLUTCH SUB-ASSEMBLY
  1. Check the clutch pinion gear teeth for wear or damage.
    If the clutch pinion gear teeth are damaged, replace the starter clutch sub-assembly and also inspect the flywheel ring gear for wear or damage.

  1. P010821
    Rotate the clutch pinion gear clockwise and check that it turns freely. Try to rotate the clutch pinion gear counterclockwise and check that it locks.
    Text in Illustration 
    V100135
    Free
    V100136
    Lock
    If the result is not as specified, replace the starter clutch sub-assembly.


INSPECT MAGNET STARTER SWITCH ASSEMBLY

  1. Check the resistance.

    1. G036853E03
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 50 - Terminal C
      Always
      Below 1 Ω

      Text in Illustration 
      *1
      Terminal C
      *2
      Terminal 50
      If the result is not as specified, replace the magnet starter switch assembly.

    2. G036854E03
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 50 - Switch body
      Always
      Below 2 Ω

      Text in Illustration 
      *1
      Terminal 50
      If the result is not as specified, replace the magnet starter switch assembly.

← DISASSEMBLY (from Aug 2013)REASSEMBLY (from Aug 2013) →