2014 Hilux · Service Manual ENGINE

P0335 Crankshaft Position Sensor "A" Circuit

Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012

Also covers:

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The crankshaft position sensor system consists of a No. 1 crankshaft position sensor plate and a pickup coil. The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of an iron core and magnet. The sensor plate rotates, and a pulse signal is created as each tooth passes by the pickup coil. The pickup coil generates 34 signals for each engine revolution. Based on these signals, the ECM calculates the crankshaft position and engine RPM. Using these calculations, the common rail injection system is controlled.
DTC No.
DTC Detection Condition
Trouble Area
P0335
When either condition below is met:
  1. No crankshaft position sensor signal to ECM while cranking
    (1 trip detection logic)
  2. No crankshaft position sensor signal to ECM at engine speed 600 rpm or more
    (1 trip detection logic)
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. No.1 crankshaft position sensor plate
  4. ECM
P0339
No crankshaft position sensor signal is input to ECM for 0.05 seconds or more, and conditions (a), (b) and (c) are met:
(1 trip detection logic)
(a) Engine speed is at 1,000 rpm or more
(b) STA signal is OFF
(c) 3 seconds or more have elapsed after STA signal is switched from ON to OFF
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. No.1 crankshaft position sensor plate
  4. ECM
A098437E04
Reference: Inspection using the oscilloscope.
While idling, the correct waveform is shown in the diagram.

HINT:
G stands for the camshaft position sensor signal, and NE stands for the crankshaft position sensor signal.
Item
Content
Terminal
(a) NE+ - NE-
Tester Range
5 V/DIV., 20 msec./DIV.
Condition
Cranking or idling


WIRING DIAGRAM

A110955E10

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
After performing the inspection procedure for the crankshaft position sensor, if DTC P0335 is output again, check the following items related to the camshaft position sensor.
  1. Installation condition of the camshaft position sensor
  2. Installation condition of the camshaft
  3. Connection of the camshaft position sensor connector

HINT:
  1. If no trouble is found in the diagnostic troubleshooting procedure of DTC P0335, troubleshoot the engine mechanical system.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. INSPECT CRANKSHAFT POSITION SENSOR

  1. A072395E28
    Disconnect the C4 crankshaft position sensor connector.

  1. Measure the resistance of the crankshaft position sensor.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Cold
    835 to 1400 Ω
    1 - 2
    Hot
    1060 to 1645 Ω

    HINT:
    In the table above, the terms "cold" and "hot" refer to the temperature of the coils in the sensors. "Cold" means approximately -10 to 50°C (14 to 122°F). "Hot" means approximately 50 to 100°C (122 to 212°F).



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

  1. A099852E12
    Disconnect the C4 crankshaft position sensor connector.

  1. Disconnect the E8 ECM connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    NE+ (C4-1) - NE+ (E8-27)
    Below 1 Ω
    NE- (C4-2) - NE- (E8-34)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    NE+ (C4-1) or NE+ (E8-27) - Body ground
    10 kΩ or higher
    NE- (C4-2) or NE- (E8-34) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK CRANKSHAFT POSITION SENSOR (SENSOR INSTALLATION)

  1. BR03795E30
    Check the sensor installation.

    OK:
    Sensor is installed correctly.



NG
TIGHTEN SENSOR
OK


4. CHECK NO. 1 CRANKSHAFT POSITION SENSOR PLATE
  1. Check the teeth of the No. 1 crankshaft position sensor plate.

    OK:
    The sensor plate's teeth do not have any cracks or deformation.



NG
REPLACE NO. 1 CRANKSHAFT POSITION SENSOR PLATE
OK

REPLACE ECM (Click here)


← P0200 Injector Circuit / Open (from Aug 2014)P0335 Crankshaft Position Sensor "A" Circuit (+ P0339) (Aug 2012 – Jul 2013) →