P0340 Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor)
Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The camshaft position sensor (G signal) consists of a magnet, iron core and pickup coil.The G signal plate (timing pulley) has one tooth on its outer circumference and is installed on the camshaft. When the camshaft rotates, the protrusion on the signal plate and the air gap on the pickup coil change, causing fluctuations in the magnetic field that generate a voltage in the pickup coil.
The NE signal plate has 34 teeth and is mounted on the crankshaft angle sensor plate. The NE signal sensor generates 34 signals for every revolution. The ECM detects the camshaft angle based on the G signal, and detects the crankshaft angle based on the NE signal.
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Crank engine for 4 seconds (STA on) |
STA on: No camshaft position sensor signal is sent to the ECM while cranking for 4 seconds or more (2 trip detection logic) |
|
| Idle engine for 1 second (STA off) |
STA off: Either condition is met (1 trip detection logic):
|
- HINT:
- If DTC P0340 is stored, the following symptoms may appear:
- Difficulty starting
- Misfire
- Combustion noise
- Black smoke
- White smoke
- Lack of power
- If DTC P0340 is stored, the following symptoms may appear:
WIRING DIAGRAM
Refer to DTC P0335 (Click here).INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
- After replacing an injector assembly, the ECM needs registration (Click here).
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- HINT:
- After performing the inspection procedure for the crankshaft position sensor, if DTC P0340 is output again, check the following items related to the camshaft position sensor.
- Installation condition of the camshaft position sensor
- Installation condition of the camshaft
- Connection of the camshaft position sensor connector
- After performing the inspection procedure for the crankshaft position sensor, if DTC P0340 is output again, check the following items related to the camshaft position sensor.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. INSPECT CAMSHAFT POSITION SENSOR |
Inspect the camshaft position sensor (Click here).
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM) |
Disconnect the camshaft position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
C1-1 - E24-13 (G+)
Always
Below 1 Ω
C1-2 - E24-14 (G-)
Always
Below 1 Ω
C1-1 or E24-13 (G+) - Body ground
Always
10 kΩ or higher
C1-2 or E24-14 (G-) - Body ground
Always
10 kΩ or higher
Reconnect the camshaft position sensor connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 3. CHECK CAMSHAFT POSITION SENSOR (SENSOR INSTALLATION) |
Check the sensor installation.

- OK:
- Sensor is installed correctly.
|
|
||||
| OK | |
| 4. CHECK CAMSHAFT TIMING PULLEY |
Check the condition of the camshaft timing pulley.
- OK:
- Timing pulley does not have any cracks or deformation.
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR CIRCUIT) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for 30 seconds or more.
Start the engine and idle it for 4 seconds or more.
Turn the tester on.
Check the engine condition while wiggling the crankshaft position sensor wire harness for 4 seconds or more when idling.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
Result Result
Proceed to
Except below
A
There are problem such as rough idle or engine stall when wire harness is wiggles, or DTC is output*
B
- HINT:
- *: As the DTC was stored due to a change in the contact resistance of the connector, repair or replace the wire harness or connector (Click here).
|
|
||||
| A | |
| 6. REPLACE ECM |
Replace the ECM (Click here).
|
|
||||
| 7. REPLACE CAMSHAFT POSITION SENSOR |
Replace the camshaft position sensor (Click here).
|
|
||||
| 8. REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
|
|
||||
| 9. SECURELY REINSTALL SENSOR |
Securely reinstall the sensor (Click here).
|
|
||||
| 10. REPLACE CAMSHAFT TIMING PULLEY |
Replace the camshaft timing pulley (Click here).
| NEXT | |
| 11. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Start the engine and idle it for 4 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| NEXT | ||
| ||
