2014 Hilux · Service Manual ENGINE

P0405 Exhaust Gas Recirculation Sensor "A" Circuit Low

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The EGR valve position sensor is mounted on the EGR valve and used for detecting the lift amount of the valve. The lift amount detected by the sensor is provided to the ECM as feedback. The ECM then regulates the lift amount of the valve in accordance with engine running conditions.
DTC No.
DTC Detection Condition
Trouble Area
P0405
EGR valve position sensor output voltage is less than 0.1 V for more than 5 seconds
(1 trip detection logic)
  1. Open or short in EGR valve position sensor circuit
  2. EGR valve position sensor
  3. ECM
P0406
EGR valve position sensor output voltage is more than 4.9 V for more than 5 seconds
(1 trip detection logic)
  1. Open or short in EGR valve position sensor circuit
  2. EGR valve position sensor
  3. ECM

MONITOR DESCRIPTION

When output voltage of the EGR valve position sensor deviates from the normal operating range of 0.1 to 4.9 V for more than 5 seconds, the ECM interprets this as a malfunction of the sensor circuit, and illuminates the MIL.

WIRING DIAGRAM

A154317E03

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK TERMINAL VOLTAGE (EGR VALVE POSITION SENSOR CONNECTOR)

  1. A148945E03
    Disconnect the E2 EGR valve position sensor connector.

  1. Measure the voltage of the wire harness side connector.

    Standard voltage:
    Tester Connection
    Specified Condition
    VC (E2-1) - E2 (E2-2)
    4.5 to 5.5 V



NG
Go to step 3
OK


2. INSPECT EGR VALVE POSITION SENSOR
A148947E02
  1. Disconnect the EGR valve position sensor connector.

  1. Measure the resistance of the EGR valve position sensor.

    Standard resistance:
    Tester Connection
    EGR Valve Condition
    Condition
    Specified Condition
    EGLS (3) - E2 (2)
    Fully opened
    20°C (68°F)
    2.0 to 7.0 kΩ
    EGLS (3) - E2 (2)
    Fully closed
    20°C (68°F)
    0.1 to 2.5 kΩ



NG
REPLACE EGR VALVE POSITION SENSOR (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)

  1. A155126E03
    Disconnect the E2 EGR valve position sensor connector.

  1. Disconnect the E7 and E8 ECM connectors.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    VC (E2-1) - VC (E8-18)
    Below 1 Ω
    EGLS (E2-3) - EGLS (E7-33)
    Below 1 Ω
    E2 (E2-2) - E2 (E8-28)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    EGLS (E2-3) or EGLS (E7-33) - Body ground
    10 kΩ or higher
    VC (E2-1) or VC (E8-18) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0405 Exhaust Gas Recirculation Sensor "A" Circuit Low (+ P0406) (Aug 2013 – Jul 2014)P0488 Exhaust Gas Recirculation Throttle Position Control Range / Performance (Jun 2011 – Jul 2012) →