P0088 Fuel Rail / System Pressure - Too High
Diagnostic trouble codes · Vehicles built Aug 2012 – Jul 2013
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| After idling for 60 seconds, repeat quick engine speed accelerations (to 2500 rpm) for 30 seconds |
The fuel pressure of the common rail exceeds 200000 kPa (2039 kgf/cm2, 29000 psi). (1 trip detection logic) |
|
| DTC No. |
Data List |
| P0088 |
|
- HINT:
- For more information on the fuel supply pump (suction control valve) and common rail system, refer to System Description (Click here).
- When DTC P0088 is stored, check the internal fuel pressure of the common rail by entering the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.
Reference Engine Speed
Fuel Press
Idling
Approximately 25000 to 35000 kPa
3000 rpm (No engine load)
Approximately 50000 to 70000 kPa
- Check "Fuel Press", "Target Common Rail Pressure" and "Target Pump SCV Current" in the freeze frame data.
- For more information on the fuel supply pump (suction control valve) and common rail system, refer to System Description (Click here).
MONITOR DESCRIPTION
- P0088 (Internal fuel pressure too high):
The ECM stores this DTC if the fuel pressure inside the common rail is more than 200000 kPa (2039 kgf/cm2, 29000 psi). This DTC indicates that: 1) the suction control valve may be stuck open, or 2) there may be a short in the suction control valve circuit.
If this DTC is stored, the ECM enters fail-safe mode and limits the engine power. The fail-safe mode continues until the ignition switch is turned off.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- After replacing the fuel supply pump, the ECM needs initialization (Click here).
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0088) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read Current DTCs.
Result Result
Proceed to
P0088
A
P0088 and "P0190, P0192 and/or P0193"
B
- HINT:
- When there is an open circuit in the fuel pressure sensor circuit, the fuel pressure sensor outputs the maximum value. Therefore, P0088 may be stored together with DTCs which indicate common rail fuel pressure sensor circuit malfunctions.
|
|
||||
| A | |
| 2. CHECK FREEZE FRAME DATA (FUEL PRESS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Record the stored DTC and freeze frame data.
Result Result
Proceed to
Value of Fuel Press is shifting towards 160000 kPa or higher in 3rd and 4th set of freeze frame data
B
Except above
A
|
|
||||
| A | |
| 3. INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE) |
Connect the positive (+) probe of an oscilloscope to the fuel pressure sensor input terminal of the ECM connector and the negative (-) probe to the body ground.

Turn the ignition switch to ON.
Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.




- Standard voltage:
Tester Connection
Condition
Specified Condition
E8-26 (PCR1) - Body ground
Vibration is applied to the wire harness and connectors
No noise in the waveform
- Result:
Result
Proceed to
MIL comes on or noise present in the waveform
B
Except above
A
|
|
||||
| A | |
| 4. REPLACE FUEL SUPPLY PUMP |
Replace the fuel supply pump (Click here).
- HINT:
- Before replacing the fuel supply pump, check that the wire harness between the suction control valve and ECM is not shorted to ground.
- When there is a malfunction in the wire harness, Target Pump SCV Current is outside the range of 923 to 1123 mA when idling, and outside the range of 1013 to 1212 mA when the engine is running at 2500 rpm without load.
- If there are no problems with the engine condition during idling, it is not necessary to perform the above wire harness inspection.
- When the wire harness between the suction control valve and ECM is not shorted to ground, it can be assumed that DTC P0088 was stored due to a malfunction in the operation of the suction control valve. Therefore, it is necessary to replace the fuel supply pump.
| NEXT | |
| 5. BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system (Click here).
| NEXT | |
| 6. PERFORM FUEL SUPPLY PUMP INITIALIZATION |
Perform fuel supply pump initialization (Click here).
| NEXT | |
| 7. CHECK DTC OUTPUT |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON and start the engine.
After idling for 60 seconds, repeat engine speed accelerations (from idling to 2500 rpm) for 30 seconds.
Confirm that the DTC is not output again.
- HINT:
- Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTC P0088.
Check the DTC judgment result.
Result Tester Display
Result
Proceed to
Pending DTC
P0088 is output
A
All Readiness
NORMAL
B
ABNORMAL
A
- HINT:
- If STATUS is INCOMPLETE or N/A, race the engine to 2500 rpm repeatedly for 30 seconds and increase the idling time.
|
|
||||
| A | |
| 8. REPLACE ECM |
Replace the ECM (Click here).
|
|
||||
| 9. REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 10. INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE) |
Connect the positive (+) probe of an oscilloscope to the fuel pressure sensor input terminal of the ECM connector and the negative (-) probe to the body ground.

Turn the ignition switch to ON.
Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the fuel pressure sensor and ECM.
- Standard voltage:
Tester Connection
Condition
Specified Condition
E8-26 (PCR1) - Body ground
Vibration is applied to the wire harness and connectors
No noise in the waveform
- Result:
Result
Proceed to
MIL comes on or noise present in the waveform
A
Except above
B
|
|
||||
| A | |
| 11. REPLACE COMMON RAIL ASSEMBLY |
Replace the common rail (Click here).
| NEXT | |
| 12. BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system (Click here).
| NEXT | |
| 13. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON and start the engine.
After idling for 60 seconds, repeat engine speed accelerations (from idling to 2500 rpm) for 30 seconds.
Confirm that the DTC is not output again.
- HINT:
- Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input DTC P0088.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, race the engine to 2500 rpm repeatedly for 30 seconds and increase the idling time.
| NEXT | ||
| ||
