2014 Hilux · Service Manual ENGINE

REMOVAL

Removal / installation · Vehicles built from Jun 2011

NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes and fuel inlet pipe, clean them with a brush and compressed air.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


2. REMOVE NO. 1 ENGINE UNDER COVER
  1. Remove the 4 bolts and under cover.


3. REMOVE NO. 2 ENGINE UNDER COVER
  1. Remove the 4 bolts and under cover.


4. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug, and drain the engine oil from the oil pan.

    NOTICE:
    Collect the oil in an oil disposal container.


5. REMOVE FUEL TANK CAP ASSEMBLY

6. REMOVE INTERCOOLER ASSEMBLY
  1. Remove the intercooler assembly (Click here).


7. REMOVE MANIFOLD STAY WITH VACUUM SWITCHING VALVE

  1. w/ EGR Cooler:

    1. Disconnect the 2 VSV connector and 3 vacuum hoses.

    2. A148131
      Remove the 2 bolts and manifold stay.

  1. w/o EGR Cooler:

    1. A099622E01
      Remove the 2 bolts and manifold stay.


8. REMOVE OIL FILTER SUB-ASSEMBLY

A147257E01
  1. Using SST, remove the oil filter.

    SST
    09228-07501  

    HINT:
    Insert the drain hose in the oil cooler cover. Put the disposal container beneath the drain hose to collect the oil from the oil cooler cover.


9. REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
  1. After removing the fuel pipe, cover the outlets on the common rail with tape to keep out foreign matter.
  2. After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.

  1. A153263E01
    Remove the 2 nuts and No. 3 injection pipe clamp.

  1. A153264E01
    Remove the 2 bolts and 2 No. 2 injection pipe clamps.

  1. A153266E05
    Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.


10. REMOVE EGR COOLER WITH ELECTRIC EGR CONTROL VALVE AND NO. 2 EGR VALVE
  1. Remove the EGR cooler with electric EGR control valve and No. 2 EGR valve (Click here).


11. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

  1. A152275
    Remove the bolt and disconnect the injection pipe clamp.

    NOTICE:
    If an injection pipe clamp is removed from the No. 4 injection pipe, replace the injection clamp with a new one.

  1. A152276E05
    Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.


12. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

  1. A152338E02
    Disconnect the 3 fuel hoses.

  1. Remove the check valve, 3 bolts, leakage pipe and gasket.


13. REMOVE FUEL INLET PIPE SUB-ASSEMBLY

  1. A152281
    Remove the bolt and clamp.

  1. A153562
    Remove the bolt and oil level gauge guide.

  1. A152282E03
    Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.


14. REMOVE COMMON RAIL ASSEMBLY
  1. Disconnect the 2 connectors.

  1. A224483
    Remove the 2 bolts, common rail and No. 2 intake manifold insulator.

    NOTICE:
    Do not remove the pressure discharge valve and pressure sensor.

← COMPONENTS (from Jun 2011)INSPECTION (from Jun 2011) →