P0488 Exhaust Gas Recirculation Throttle Position Control Range / Performance
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The ECM opens and closes the throttle valve using a rotary solenoid type actuator. Due to opening and closing the valve, the exhaust gas recirculation volume can be properly controlled. Also, engine vibration and noise will be reduced by closing the valve when the engine is stopped.| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0488 |
|
|
- HINT:
- After confirming DTC P0488, check the throttle position.
Reference: Condition
Throttle Valve Position
Moment when accelerator pedal is further depressed or released at 3,000 rpm
Opening angle varies smoothly
MONITOR DESCRIPTION
The ECM opens and closes the throttle valve by adjusting the current flowing to the rotary solenoid with a duty ratio. If the throttle valve does not move smoothly or is stuck, the duty ratio used during valve movement control increases or decreases greatly, and the ECM will determine that the throttle valve is malfunctioning and the ECM illuminates the MIL.

WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- After warming up the engine, DTC P0488 can be set if 1 second or more passes after quickly accelerating the engine from idling.
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
- After warming up the engine, DTC P0488 can be set if 1 second or more passes after quickly accelerating the engine from idling.
| 1. CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P0488) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
- Result:
Display (DTC Output)
Proceed to
P0488
A
P0488, P0122 and/or P0123
B
- HINT:
- If codes other than P0488 are output, perform troubleshooting for those DTCs first.
|
|
||||
| A | |
| 2. CHECK IF DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine / DTC / Clear.
Clear the DTCs.
Start the engine and accelerate the engine from idle to 3,000 rpm 3 times quickly.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
- Result:
Display (DTC output)
Proceed to
P0488
A
No output
B
- HINT:
- The normal operation of the throttle valve is as follows.
Reference: Condition
Throttle Valve Position
Moment when accelerator pedal is further depressed or released at 3,000 rpm
Opening angle varies smoothly
|
|
||||
| A | |
| 3. INSPECT THROTTLE CONTROL MOTOR |
Disconnect the T1 throttle control motor.

Turn the ignition switch ON.
Measure the voltage of the wire harness side connector.
- Standard voltage:
Tester Connection
Specified Condition
B (T1-2) - Body ground
11 to 14 V
- Standard resistance (Check for open):
Tester Connection
Specified Condition
RSC (T1-3) - Body ground
Below 1 Ω
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (THROTTLE CONTROL MOTOR - ECM) |
Disconnect the T1 throttle control motor connector.

Disconnect the E7 ECM connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
RSO (T1-1) - LUSL (E7-4)
Below 1 Ω
- Standard resistance (Check for short):
Tester Connection
Specified Condition
RSO (T1-1) or LUSL (E7-4) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 5. REPLACE DIESEL THROTTLE BODY ASSEMBLY |
Replace diesel throttle body assembly (Click here).
| NEXT | |
| 6. CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester ON.
Enter the following menu: Powertrain / Engine / DTC / Clear.
Clear DTCs.
Start the engine and warm it up.
Accelerate the engine from idle to 3,000 rpm 3 times quickly.
Select the following menu items: Powertrain / Engine / DTC.
Read DTCs.
- Result:
Display (DTC Output)
Proceed to
P0488
A
No output
B
|
|
||||
| A | ||
| ||
