2014 Hilux · Service Manual ENGINE

P0180 Fuel Temperature Sensor "A" Circuit

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The fuel temperature sensor monitors the fuel temperature. The fuel temperature sensor has a thermistor that varies its resistance depending on the fuel temperature. When the fuel temperature is low, the resistance of the thermistor is high. When the temperature is high, the resistance is low. The variations of resistance are communicated to the ECM as changes of voltage (see Fig. 1).
The fuel temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the fuel temperature sensor from terminal THF via resistor R.
The resistor R and fuel temperature sensor are connected in series. When the resistance value of the fuel temperature sensor changes due to a change of fuel temperature, the voltage at terminal THF also changes. Based on this signal, the ECM corrects the pressure control compensation of the supply pump and determines errors.
G036559E03
DTC No.
DTC Detection Condition
Trouble Area
P0180
Open or short in fuel temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
  1. Open or short in fuel temperature sensor circuit
  2. Fuel temperature sensor
  3. ECM
P0182
Short in fuel temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
  1. Open or short in fuel temperature sensor circuit
  2. Fuel temperature sensor
  3. ECM
P0183
Open in fuel temperature sensor circuit for 0.5 seconds
(1 trip detection logic)
  1. Open or short in fuel temperature sensor circuit
  2. Fuel temperature sensor
  3. ECM

HINT:
When DTC P0180, P0182 and/or P0183 is set, check the fuel temperature by entering the following menus on the intelligent tester: Powertrain / Engine / Data List / Fuel Temperature.


Reference:
Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
140°C (284°F) or more
Short circuit


WIRING DIAGRAM

A110952E12

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
  1. If different DTCs related to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (FUEL TEMPERATURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Fuel Temperature.

  1. Read the value displayed on the intelligent tester.

    OK:
    Same value as the actual fuel temperature.


    Result:
    Temperature Displayed
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F) or more
    B
    OK (Same as actual fuel temperature)
    C

    HINT:
    1. If there is an open circuit, the intelligent tester indicates -40°C (-40°F).
    2. If there is a short circuit, the intelligent tester indicates 140°C (284°F) or more.



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

  1. A117996E07
    Disconnect the F11 fuel temperature sensor connector.

  1. Connect terminals 1 and 2 of the fuel temperature sensor wire harness side connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Fuel Temperature.

  1. Read the value.

    Standard:
    140°C (284°F)



OK
REPLACE FUEL TEMPERATURE SENSOR (Click here)
NG


3. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN ECM)

  1. A099842E45
    Disconnect the F11 fuel temperature sensor connector.

  1. Connect terminals THF and E2 of the E8 ECM connector.

    HINT:
    Before checking, do a visual and contact pressure check on the ECM connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Fuel Temperature.

  1. Read the value displayed.

    Standard:
    140°C (284°F)



OK
REPAIR OR REPLACE HARNESS OR CONNECTOR
NG

CONFIRM GOOD CONNECTION AT ECM. IF OK, REPLACE ECM (Click here)

4. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

  1. A083863E42
    Disconnect the F11 fuel temperature sensor connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the intelligent tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Fuel Temperature.

  1. Read the value.

    Standard:
    -40°C (-40°F)



OK
REPLACE FUEL TEMPERATURE SENSOR (Click here)
NG


5. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN ECM)

  1. A099830E15
    Disconnect the F11 fuel temperature sensor connector.

  1. Disconnect the E8 ECM connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Enter the following menus: Powertrain / Engine / Data List / Fuel Temperature.

  1. Read the value.

    Standard:
    -40°C (-40°F)



OK
REPAIR OR REPLACE HARNESS OR CONNECTOR
NG

REPLACE ECM (Click here)


← P0180 Fuel Temperature Sensor "A" Circuit (+ P0182, P0183) (Aug 2013 – Jul 2014)P0191 Fuel Rail Pressure Sensor Circuit Range / Performance (Jun 2011 – Jul 2012) →