P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance
Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
Refer to DTC P2120 (Click here).| DTC No. |
DTC Detection Condition |
Trouble Area |
| P2121 |
Condition (a) continues for 2 seconds: (a) Difference between VPA1 and VPA2 exceeds the threshold (1 trip detection logic) |
|
WIRING DIAGRAM
Refer to DTC P2120 (Click here).INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. READ VALUE USING INTELLIGENT TESTER (ACCEL SENS. NO.1 VOLT % AND ACCEL SENS. NO.2 VOLT %) |
Connect the intelligent tester to the DLC3.

Turn the ignition switch ON and turn the tester ON.
Enter the following menus: Powertrain / Engine / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.
Read the values.
- Standard:
Accelerator Pedal
Accel Sens. No.1 Volt %
Accel Sens. No.2 Volt %
Released
10 to 22%
24 to 40%
Depressed
52 to 90%
68 to 99%
|
|
||||
| NG | |
| 2. CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM) |
Disconnect the A13 sensor connector.

Disconnect the E5 ECM connector.
Measure the resistance of the wire harness side connectors.
- Standard resistance (Check for open):
Tester Connection
Specified Condition
VCP2 (A13-1) - VCP2 (E5-27)
Below 1 Ω
EPA2 (A13-2) - EPA2 (E5-29)
Below 1 Ω
VPA2 (A13-3) - VPA2 (E5-23)
Below 1 Ω
VCPA (A13-4) - VCPA (E5-26)
Below 1 Ω
EPA (A13-5) - EPA (E5-28)
Below 1 Ω
VPA (A13-6) - VPA (E5-22)
Below 1 Ω
- Standard resistance (Check for short):
Tester Connection
Specified Condition
VCP2 (A13-1) or VCP2 (E5-27) - Body ground
10 kΩ or higher
EPA2 (A13-2) or EPA2 (E5-29) - Body ground
10 kΩ or higher
VPA2 (A13-3) or VPA2 (E5-23) - Body ground
10 kΩ or higher
VCPA (A13-4) or VCPA (E5-26) - Body ground
10 kΩ or higher
EPA (A13-5) or EPA (E5-28) - Body ground
10 kΩ or higher
VPA (A13-6) or VPA (E5-22) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 3. REPLACE ACCELERATOR PEDAL ROD ASSEMBLY |
Replace the accelerator pedal rod assembly (Click here).
| NEXT | |
| 4. CHECK WHETHER DTC OUTPUT RECURS (DTC P2121) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON and turn the tester ON.
Clear DTCs (Click here).
Start the engine.
Allow the engine to idle for 15 seconds.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
- Result:
Display (DTC Output)
Proceed to
P2121
A
No output
B
|
|
||||
| A | ||
| ||
