2014 Hilux · Service Manual ENGINE

P20CB Exhaust Aftertreatment Fuel Injector "A" Control Circuit Stuck Open

Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012

Also covers:

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

A248426E01
The exhaust fuel addition injector is mounted on the outlet of the turbocharger sub-assembly, and low pressure fuel is supplied to the injector by the feed pump in the supply pump. This injector adds fuel by a control signal from the ECM.
This injector is used for two different controls: PM forced regeneration and PM reduction.
During PM forced regeneration, the injector adds fuel to raise the catalyst temperature.
In the other control, the injector helps the air-fuel ratio become rich. As a result, PM in the exhaust gas will be reduced in response to the rich air-fuel ratio.

HINT:
  1. For more information on the exhaust fuel addition injector and DPF, refer to the following procedures (Click here).
  2. If P20CB, P20CD and P20CE are present, refer to the DTC table for Diesel Particulate Filter System (Click here).

P20CB 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 3 seconds
With the exhaust fuel addition injector off, the FIVM1 output is high and the FIVM2 output is low for 3 seconds.
(1 trip detection logic)
  1. Open in exhaust fuel addition injector assembly circuit
  2. Exhaust fuel addition injector assembly
  3. ECM
P20CD 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 1 second
With the exhaust fuel addition injector off, the FIVM1 output is high and the FIVM2 output is high for 0.16 seconds.
(1 trip detection logic)
  1. Open in exhaust fuel addition injector assembly circuit
  2. Exhaust fuel addition injector assembly
  3. ECM
P20CE 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Drive vehicle for 20 minutes (exhaust gas temperature is 250°C (482°F) or higher).
With the exhaust fuel addition injector on, the FIVM1 output is low and the FIVM2 output is low 7 or more times.
(1 trip detection logic)
  1. Open in exhaust fuel addition injector assembly circuit
  2. Exhaust fuel addition injector assembly
  3. ECM

HINT:
DTC P200C and/or P20CF will be present if there is an open malfunction in the exhaust fuel addition injector circuit.


MONITOR DESCRIPTION

In order to detect abnormality in the fuel addition injector, an internal CPU of the ECM monitors injection command (FIV) signals and injection confirmation (FIVM) signals. The FIV signal is sent from the CPU to the exhaust fuel addition injector via a drive circuit inside the ECM. The FIVM signal, which is originally output current from the internal drive circuit of the ECM, is transmitted to the CPU via a monitor circuit. By receiving the FIVM signal, the ECM judges that the current has been applied to the exhaust fuel addition injector.
This DTC will be set if the ECM judges that the number of signals of the FIV and FIVM are inconsistent.
A117827E05

WIRING DIAGRAM

A258903E05

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  3. After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
  4. After replacing an injector assembly, the ECM needs registration (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. INSPECT EXHAUST FUEL ADDITION INJECTOR ASSEMBLY (RESISTANCE)
  1. Inspect the exhaust fuel addition injector assembly (Click here).



NG
Go to step 5
OK


2. CHECK TERMINAL VOLTAGE (POWER SOURCE)

  1. A204917E17
    Disconnect the exhaust fuel addition injector assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E32-2 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Exhaust Fuel Addition Injector Assembly)

  1. Reconnect the exhaust fuel addition injector assembly connector.



NG
Go to step 6
OK


3. CHECK HARNESS AND CONNECTOR (EXHAUST FUEL ADDITION INJECTOR ASSEMBLY - ECM)
  1. Disconnect the exhaust fuel addition injector assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E32-1 - E25-5 (FIV)
    Always
    Below 1 Ω
    E32-1 or E25-5 (FIV) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the exhaust fuel addition injector assembly connector.

  1. Reconnect the ECM connector.



NG
Go to step 6
OK


4. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 7
5. REPLACE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY
  1. Replace the exhaust fuel addition injector assembly (Click here).



NEXT
Go to step 7
6. REPAIR OR REPLACE HARNESS OR CONNECTOR

HINT:
If the voltage at the exhaust fuel addition injector assembly connector is not 11 to 14 V, repair or replace the harness and connector between the exhaust fuel addition injector assembly and EFI MAIN relay (including the EFI No. 2 fuse).

  1. Repair or replace the harness or connector.


NEXT


7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Drive the vehicle for 20 minutes.

    HINT:
    The exhaust gas temperature increases to 250°C (482°F) or higher after driving the vehicle for 20 minutes.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END


← P2084 Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 2 (+ P242B) (from Aug 2014)P20CB Exhaust Aftertreatment Fuel Injector "A" Control Circuit Stuck Open (+ P20CD, P20CE) (Aug 2012 – Jul 2013) →