21 Solar Sensor Circuit
Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
DESCRIPTION


The cooler thermistor (solar sensor), which is installed on the upper side of the instrument panel, detects sunlight and controls the air conditioning in AUTO mode. The output current from the cooler thermistor (solar sensor) varies according to the amount of sunlight. When the amount of sunlight increases, the output current increases. As the amount of sunlight decreases, the output current decreases. The air conditioning amplifier assembly detects the output current from the cooler thermistor (solar sensor).
| DTC Code |
Detection Item |
Trouble Area |
| 21 |
An open in cooler thermistor (solar sensor) circuit (If check is performed in a dark place, DTC 21 may be stored) |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- If the check is performed in a dark place, DTC 21 may be stored even though the system is normal.
| 1. CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY |
Remove the air conditioning amplifier assembly with its connectors still connected (Click here).

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
A46-2 (S5-3) - A46-7 (TS)
- Ignition switch ON
- Solar sensor subjected to electric light
- Vehicle indoors
0.8 to 4.3 V
- Ignition switch ON
- Solar sensor covered with a cloth
- Vehicle indoors
Below 0.8 V
- Ignition switch ON
Text in Illustration *a
Component with harness connected
(Air Conditioning Amplifier Assembly)
- HINT:
- As the inspection light is moved away from the sensor, the voltage decreases.
- Use an incandescent light for inspection. Bring it within 30 cm (11.8 in.) of the sensor.
- As the inspection light is moved away from the sensor, the voltage decreases.
Result Result
Proceed to
OK (When troubleshooting according to problem symptoms table.)
A
OK (When troubleshooting according to DTC.)
B
NG
C
|
|
||||
|
|
||||
| A | ||
| ||
| 2. INSPECT COOLER THERMISTOR (SOLAR SENSOR) |
Remove the cooler thermistor (solar sensor) (Click here).

Measure the resistance according to the value(s) in the table below.
Connect the positive (+) lead of the ohmmeter to terminal 2 and the negative (-) lead to terminal 1 of the cooler thermistor.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
- Vehicle indoors
- Solar sensor is subjected to electric light
Below 10 kΩ
- Vehicle indoors
- Solar sensor is covered with a cloth
10 kΩ or higher
- Vehicle indoors
- NOTICE:
- The connection procedure for a digital tester, such as a TOYOTA electrical tester, is shown above. When using an analog tester, connect the negative (-) lead to terminal 2 and positive (+) lead to terminal 1.
- HINT:
- As the inspection light is moved away from the cooler thermistor (solar sensor), the resistance increases.
- Use an incandescent light for inspection. Bring it within 30 cm (11.8 in.) from the sensor.
- As the inspection light is moved away from the cooler thermistor (solar sensor), the resistance increases.
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (SOLAR SENSOR - AIR CONDITIONING AMPLIFIER) |
Disconnect the A35 cooler thermistor (solar sensor) connector.
Disconnect the A46 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A46-2 (S5-3) - A35-1
Always
Below 1 Ω
A46-7 (TS) - A35-2
A46-2 (S5-3) - Body ground
Always
10 kΩ or higher
A46-7 (TS) - Body ground
|
|
||||
| OK | ||
| ||
