2014 Hilux · Service Manual ENGINE

U0101 Lost Communication with TCM

Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The ECM (engine control unit) communicates with the TCM (transmission control ECU) through the Controller Area Network (CAN).
If there is a problem with this communication, the ECM stores a DTC.
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 3 seconds
Both conditions are met for 1.25 seconds (1 trip detection logic):
  1. The battery voltage is 10.5 V or higher.
  2. No communication between the ECM and TCM.
  1. ECM
  2. TCM
  3. ECM to TCM circuit

WIRING DIAGRAM

A227728E02

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  3. After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
  4. After replacing an injector assembly, the ECM needs registration (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC U0101)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    U0101 is output
    A
    U0101 and other DTCs are output
    B

    HINT:
    If any DTCs other than U0101 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. INSPECT TCM POWER SOURCE CIRCUIT (POWER SOURCE AND BODY GROUND)

  1. C216560E07
    Disconnect the TCM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    T38-5 (BATT) - T19-1 (E1)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to TCM)

  1. Reconnect the TCM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (ECM - TCM)
  1. Disconnect the TCM connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E24-24 (CAN+) - T38-21 (CAN+)
    Always
    Below 1 Ω
    E24-18 (CAN-) - T38-20 (CAN-)
    Always
    Below 1 Ω
    E24-24 (CAN+) or T38-21 (CAN+) - Body ground or other terminals
    Always
    1 MΩ or higher
    E24-18 (CAN-) or T38-20 (CAN-) - Body ground or other terminals
    Always
    1 MΩ or higher

  1. Reconnect the TCM connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


5. CHECK WHETHER DTC OUTPUT RECURS (DTC U0101)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    No DTC is output
    A
    U0101 is output
    B



B
REPLACE TCM
A

END


← P2610 ECM / PCM Internal Engine Off Timer Performance (from Aug 2014)U0101 Lost Communication with TCM (Aug 2012 – Jul 2013) →