U0101 Lost Communication with TCM
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The ECM (engine control unit) communicates with the TCM (transmission control ECU) through the Controller Area Network (CAN).If there is a problem with this communication, the ECM stores a DTC.
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Ignition switch ON for 3 seconds |
Both conditions are met for 1.25 seconds (1 trip detection logic):
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
- After replacing an injector assembly, the ECM needs registration (Click here).
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC U0101) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
Result Result
Proceed to
U0101 is output
A
U0101 and other DTCs are output
B
- HINT:
- If any DTCs other than U0101 are output, troubleshoot those DTCs first.
|
|
||||
| A | |
| 2. INSPECT TCM POWER SOURCE CIRCUIT (POWER SOURCE AND BODY GROUND) |
Disconnect the TCM connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
T38-5 (BATT) - T19-1 (E1)
Ignition switch ON
11 to 14 V
Text in Illustration *a
Rear view of wire harness connector
(to TCM)
Reconnect the TCM connector.
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (ECM - TCM) |
Disconnect the TCM connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E24-24 (CAN+) - T38-21 (CAN+)
Always
Below 1 Ω
E24-18 (CAN-) - T38-20 (CAN-)
Always
Below 1 Ω
E24-24 (CAN+) or T38-21 (CAN+) - Body ground or other terminals
Always
10 kΩ or higher
E24-18 (CAN-) or T38-20 (CAN-) - Body ground or other terminals
Always
10 kΩ or higher
Reconnect the TCM connector.
Reconnect the ECM connector.
|
|
||||
| OK | |
| 4. REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 5. CHECK WHETHER DTC OUTPUT RECURS (DTC U0101) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
Result Result
Proceed to
No DTC is output
A
U0101 is output
B
|
|
||||
| A | ||
| ||
