2014 Hilux · Service Manual BODY ELECTRICAL

Display Signal Circuit between Navigation Receiver Assembly and Television Camera Assembly

Circuit diagnosis · Vehicles built from Aug 2013

DESCRIPTION

This is the display signal circuit between the navigation receiver assembly and the rear television camera assembly.

WIRING DIAGRAM

E275627E08

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
  1. Disconnect the N10 navigation receiver assembly connector.

  1. Disconnect the R25 rear television camera assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N10-11 (CA+) - R25-4 (CB+)
    Always
    Below 1 Ω
    N10-12 (V+) - R25-2 (CV+)
    Always
    Below 1 Ω
    N10-23 (CGND) - R25-3 (CGND)
    Always
    Below 1 Ω
    N10-24 (V-) - R25-1 (CV-)
    Always
    Below 1 Ω
    N10-11 (CA+) - Body ground
    Always
    10 kΩ or higher
    N10-12 (V+) - Body ground
    Always
    10 kΩ or higher
    N10-23 (CGND) - Body ground
    Always
    10 kΩ or higher
    N10-24 (V-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. INSPECT NAVIGATION RECEIVER ASSEMBLY

  1. E275624E08
    Disconnect the N10 navigation receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N10-23 (CGND) - Body ground
    Always
    Below 1 Ω
    N10-24 (V-) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Navigation Receiver Assembly)



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


3. CHECK NAVIGATION RECEIVER ASSEMBLY

  1. E227664E26
    Disconnect the R25 rear television camera assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    R25-4 (CB+) - R25-3 (CGND)
    Ignition switch ACC
    5.5 to 7.05 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Rear Television Camera Assembly)



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


4. CHECK REAR TELEVISION CAMERA ASSEMBLY

  1. Using an oscilloscope, check the waveform.E275625E11

    Text in Illustration 
    *a
    Component with harness connected
    (Navigation Receiver Assembly)
    *b
    Waveform 1
    *c
    Waveform 2
    *d
    Synchronized Signal
    *e
    Video Waveform
    -
    -
    Measurement Condition 
    Item
    Content
    Tester Connection
    N10-12 (V+) - N10-24 (V-)
    Tool Setting
    0.2 V/DIV., 50 μs/DIV.
    Condition
    1. Waveform 1: Ignition switch ON, shift lever in R
    2. Waveform 2: Ignition switch ON, shift lever in R, screen blacked out by covering camera lens

    OK:
    Waveform is as shown in illustration.

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.



NG
REPLACE REAR TELEVISION CAMERA ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Reverse Signal Circuit (from Aug 2013)COMPONENTS (from Jun 2011) →