2014 Hilux · Service Manual BODY ELECTRICAL

Reverse Signal Circuit

Circuit diagnosis · Vehicles built from Aug 2013

DESCRIPTION

The navigation receiver assembly receives a reverse signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2.
  1. *1: for Automatic Transmission
  2. *2: for Manual Transmission

WIRING DIAGRAM

E227687E26

INSPECTION PROCEDURE


1. CHECK VEHICLE SIGNAL (OPERATION CHECK)

  1. E278094
    Enter the "Function Check/Setting" screen and select "Vehicle Signal" (Click here).

  1. Check that the display changes between ON and OFF according to the shift lever position.

    OK:
    Shift Lever Position
    Display
    R
    ON
    Except R
    OFF

    HINT:
    This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.



NG
Go to step 2
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. CHECK NAVIGATION RECEIVER ASSEMBLY
E140414E78
  1. Disconnect the N9 navigation receiver assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    N9-2 (REV) - Body ground
    Ignition switch ON, shift lever in R
    7.5 to 14 V
    N9-2 (REV) - Body ground
    Ignition switch ON, shift lever not in R
    Below 1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Navigation Receiver Assembly)
    Result 
    Result
    Proceed to
    OK
    A
    NG (for Automatic Transmission)
    B
    NG (for Manual Transmission)
    C



B
Go to step 3

C
Go to step 4
A

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)

3. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
  1. Disconnect the N9 navigation receiver assembly connector.

  1. Disconnect the N8 park/neutral position switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N9-2 (REV) - N8-1 (RL)
    Always
    Below 1 Ω
    N9-2 (REV) - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK (for A750E)
    A
    OK (for A750F)
    B
    NG
    C



B
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)

4. CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)
  1. Disconnect the N9 navigation receiver assembly connector.

  1. Disconnect the B1 back-up light switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N9-2 (REV) - B1-1
    Always
    Below 1 Ω
    N9-2 (REV) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BACK-UP LIGHT SWITCH ASSEMBLY (Click here)


← Screen Flicker or Color Distortion (from Aug 2013)Display Signal Circuit between Navigation Receiver Assembly and Television Camera Assembly (from Aug 2013) →