2014 Hilux · Service Manual COMMUNICATION SYSTEM

Check CAN Bus Line for Short to GND

Circuit diagnosis · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

There may be a short circuit between the CAN bus lines and GND when the resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.
Symptom
Trouble Area
The resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.
  1. Short to GND
  2. Brake actuator assembly (skid control ECU)
  3. Spiral cable (steering angle sensor)
  4. Yaw rate sensor
  5. ECM
  6. No. 1 junction connector
  7. No. 2 junction connector
  8. No. 3 junction connector

WIRING DIAGRAM

C245036E01

INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR SHORT TO GND IN CAN BUS WIRE (DLC3 BRANCH WIRE)

  1. H102621E30
    Disconnect the J49 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Measured Resistance
    D1-6 (CANH) - D1-4 (CG)
    Ignition switch off
    200 Ω or higher
    D1-14 (CANL) - D1-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


3. CONNECT CONNECTOR
  1. Reconnect the J49 No. 3 junction connector.


NEXT


4. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR SIDE)

  1. H102621E30
    Disconnect the J54 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Measured Resistance
    D1-6 (CANH) - D1-4 (CG)
    Ignition switch off
    200 Ω or higher
    D1-14 (CANL) - D1-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
Go to step 11
OK


5. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - SKID CONTROL ECU)

  1. C190790E12
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Measured Resistance
    J54-13 (CANH) - D1-4 (CG)
    Ignition switch off
    200 Ω or higher
    J54-7 (CANL) - D1-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
Go to step 7
OK


6. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ECM)

  1. C190790E13
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Measured Resistance
    J54-12 (CANH) - D1-4 (CG)
    Ignition switch off
    200 Ω or higher
    J54-6 (CANL) - D1-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
Go to step 9
OK

REPLACE NO. 1 JUNCTION CONNECTOR

7. CONNECT CONNECTOR
  1. Reconnect the J54 No. 1 junction connector.


NEXT


8. CHECK FOR SHORT TO GND IN CAN BUS WIRE (SKID CONTROL ECU)

  1. C245062E02
    Disconnect the S35 skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Measured Resistance
    S35-25 (CANH) - D1-4 (CG)
    Ignition switch off
    200 Ω or higher
    S35-14 (CANL) - D1-4 (CG)
    Ignition switch off
    200 Ω or higher

    Result 
    Result
    Proceed to
    OK (for LHD)
    A
    OK (for RHD)
    B
    NG
    C



B
REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)

C
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)
A

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU) (Click here)

9. CONNECT CONNECTOR
  1. Reconnect the J54 No. 1 junction connector.


NEXT


10. CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM)

  1. C245063E02
    for 1KD-FTV, 2KD-FTV (w/ DPF):
    1. Disconnect the E30 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Measured Resistance
      E30-35 (CANH) - D1-4 (CG)
      Ignition switch off
      200 Ω or higher
      E30-36 (CANL) - D1-4 (CG)
      Ignition switch off
      200 Ω or higher

  1. C245064E02
    for 1KD-FTV, 2KD-FTV (w/o DPF):
    1. Disconnect the E6 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Measured Resistance
      E6-24 (CANH) - D1-4 (CG)
      Ignition switch off
      200 Ω or higher
      E6-23 (CANL) - D1-4 (CG)
      Ignition switch off
      200 Ω or higher

  1. C245065E02
    for 1GR-FE:
    1. Disconnect the E13 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Measured Resistance
      E13-33 (CANH) - D1-4 (CG)
      Ignition switch off
      200 Ω or higher
      E13-34 (CANL) - D1-4 (CG)
      Ignition switch off
      200 Ω or higher

Result 
Result
Proceed to
OK (for 1KD-FTV)
A
OK (for 2KD-FTV)
B
OK (for 1GR-FE)
C
NG
D


B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
A

REPLACE ECM (Click here)

11. CONNECT CONNECTOR
  1. Reconnect the J54 No. 1 junction connector.


NEXT


12. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

  1. C245066E03
    Disconnect the J59 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Measured Resistance
    J59-5 (CANH) - D1-4 (CG)
    Ignition switch off
    200 Ω or higher
    J59-16 (CANL) - D1-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
OK


13. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR SIDE)

  1. H102621E30
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Measured Resistance
    D1-6 (CANH) - D1-4 (CG)
    Ignition switch off
    200 Ω or higher
    D1-14 (CANL) - D1-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
Go to step 17
OK


14. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - YAW RATE SENSOR)

  1. C245066E04
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Measured Resistance
    J59-7 (CANH) - D1-4 (CG)
    Ignition switch off
    200 Ω or higher
    J59-18 (CANL) - D1-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
Go to step 15
OK

REPLACE NO. 2 JUNCTION CONNECTOR

15. CONNECT CONNECTOR
  1. Reconnect the J59 No. 2 junction connector.


NEXT


16. CHECK FOR SHORT TO GND IN CAN BUS WIRE (YAW RATE SENSOR)

  1. C245067E02
    Disconnect the Y1 yaw rate sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Measured Resistance
    Y1-3 (CANH) - D1-4 (CG)
    Ignition switch off
    200 Ω or higher
    Y1-2 (CANL) - D1-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO YAW RATE SENSOR (CANH, CANL)
OK

REPLACE YAW RATE SENSOR (Click here)

17. CONNECT CONNECTOR
  1. Reconnect the J59 No. 2 junction connector.


NEXT


18. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

  1. C190792E12
    Disconnect the J50 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Measured Resistance
    J50-2 (CANH) - D1-4 (CG)
    Ignition switch off
    200 Ω or higher
    J50-1 (CANL) - D1-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK


19. CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - STEERING ANGLE SENSOR)

  1. C190792E13
    Disconnect the J51 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Measured Resistance
    J51-2 (CANH) - D1-4 (CG)
    Ignition switch off
    200 Ω or higher
    J51-1 (CANL) - D1-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
Go to step 20
OK

REPLACE NO. 3 JUNCTION CONNECTOR

20. CONNECT CONNECTOR
  1. Reconnect the J50 and J51 No. 3 junction connectors.


NEXT


21. CHECK FOR SHORT TO GND IN CAN BUS WIRE (STEERING ANGLE SENSOR)

  1. C245068E02
    Disconnect the S37 steering angle sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Measured Resistance
    S37-4 (CANH) - D1-4 (CG)
    Ignition switch off
    200 Ω or higher
    S37-3 (CANL) - D1-4 (CG)
    Ignition switch off
    200 Ω or higher



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO STEERING ANGLE SENSOR (CANH, CANL)
OK

REPLACE SPIRAL CABLE (STEERING ANGLE SENSOR) (Click here)


← Check CAN Bus Line for Short to +B (from Aug 2014)Check CAN Bus Line for Short to GND (Aug 2012 – Jul 2013) →