2014 Hilux · Service Manual ENGINE

P0047 Turbocharger/Supercharger Boost Control "A" Circuit Low

Diagnostic trouble codes · Vehicles built from Aug 2014

Also covers:

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Refer to DTC P0046 (Click here).
DTC No.
DTC Detection Condition
Trouble Area
P0047
All of following conditions met for 1 second or more
(1 trip detection logic):
  1. DC motor duty ratio 100%
  2. DC motor current 0.5 A or less
  1. Open in DC motor circuit
  2. Turbo motor driver
  3. DC Motor (Turbocharger sub-assembly)
P0048
DC motor current 6.5 A or more for 0.5 seconds or more
(1 trip detection logic)
  1. Short in DC motor circuit
  2. Turbo motor driver
  3. DC Motor (Turbocharger sub-assembly)

WIRING DIAGRAM

Refer to DTC P0046 (Click here).

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR OPERATION)
  1. Turn the ignition switch ON.

  1. Turn the ignition switch OFF and check the DC motor operation.

    OK:
    When ignition switch is turned OFF, operation link moves as shown in A to D in illustration below.

A158317E01


OK
CHECK FOR INTERMITTENT PROBLEMS (Click here)
NG


2. INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR)

  1. G036521E03
    Disconnect the T10 DC motor connector.

  1. Measure the resistance of the DC motor.

    Standard resistance:
    Tester Connection
    Specified Condition
    M+ (2) - M- (1)
    1 to 100 Ω



NG
REPLACE TURBOCHARGER SUB-ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (DC MOTOR - TURBO MOTOR DRIVER)

  1. A150170E08
    Disconnect the T10 DC motor connector.

  1. Disconnect the T8 turbo motor drive connector.

  1. Measure the resistance of the wire harness side connectors.

    Standard resistance (Check for open):
    Tester Connection
    Specified Condition
    M+ (T8-12) - M+ (T10-2)
    Below 1 Ω
    M- (T8-5) - M- (T10-1)
    Below 1 Ω

    Standard resistance (Check for short):
    Tester Connection
    Specified Condition
    M+ (T8-12) or M+ (T10-2) - Body ground
    10 kΩ or higher
    M- (T8-5) or M- (T10-1) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. REPLACE TURBO MOTOR DRIVER

NEXT


5. CHECK IF DTC OUTPUT RECURS (DTC P0047 AND/OR P0048)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch ON and turn the tester ON.

  1. Clear the DTC (Click here).

  1. Start the engine.

  1. Perform the test drive.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result:
    Display (DTC Output)
    Proceed to
    P0047 and/or P0048
    A
    No output
    B



B
END
A

REPLACE TURBOCHARGER SUB-ASSEMBLY (Click here)


← P0047 Turbocharger/Supercharger Boost Control "A" Circuit Low (+ P0048) (Aug 2013 – Jul 2014)P0087 Fuel Rail / System Pressure - Too Low (+ P0190, P0192, P0193) (Jun 2011 – Jul 2012) →