2014 Hilux · Service Manual ENGINE

INSPECTION

Inspection · Vehicles built from Aug 2012

Versions by build date: Jun 2011 – Jul 2012 from Aug 2012


INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ Intercooler)

  1. A246466E01
    Inspect the electric EGR control valve.
    Text in Illustration 
    *1
    Cap

    HINT:
    Install a cap to block the other port.


    1. When a vacuum of 27 kPa (200 mmHg, 7.88 in.Hg) is applied to the diaphragm chamber, check that the shaft rises and that air flows out.

    2. While maintaining the above conditions, check that there are no leaks and that the shaft stays in position.

    3. Check that the valve does not have heavy carbon deposits and is not stuck.
      If the result is not as specified, replace the electric EGR control valve.

  1. Inspect the EGR valve position sensor.

    1. A085764E05
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1 (VC) - 2 (E2)
      20°C (68°F)
      2.8 to 7.8 kΩ

      Text in Illustration 
      *a
      Component without harness connected
      (Electric EGR Control Valve)
      If the result is not as specified, replace the electric EGR control valve assembly.

  1. Create a vacuum in the diaphragm chamber.

    HINT:
    Install a cap to block the other port.

  1. A246467E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (EGLS) - 2 (E2)
    20°C (68°F)
    EGR valve is fully opened
    2.0 to 7.0 kΩ
    20°C (68°F)
    EGR valve is fully closed
    0.1 to 2.5 kΩ

    Text in Illustration 
    *1
    Cap
    *a
    Component without harness connected
    (Electric EGR Control Valve)

    HINT:
    The resistance increases in proportion to the opening amount of the EGR valve.

    If the result is not as specified, replace the electric EGR control valve assembly.


INSPECT ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/o Intercooler)

  1. A099571E02
    Inspect the electric EGR control valve.

    1. When a vacuum of 27 kPa (200 mmHg, 7.88 in.Hg) is applied to the diaphragm chamber, check that the shaft rises and air flows out.

    2. While maintaining the above conditions, check that there are no leaks and that the shaft stays in position.

    3. Check that the valve does not have heavy carbon deposits and is not stuck.
      If the result is not as specified, replace the electric EGR control valve assembly.

  1. Inspect the EGR valve position sensor.

    1. A085764E07
      Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      1 (VC) - 2 (E2)
      20°C (68°F)
      2.8 to 7.8 kΩ

      Text in Illustration 
      *a
      Component without harness connected
      (Electric EGR Control Valve)
      If the result is not as specified, replace the electric EGR control valve assembly.

  1. Create a vacuum in the diaphragm chamber.

  1. A099572E08
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 (EGLS) - 2 (E2)
    20°C (68°F)
    EGR valve is fully opened
    2.0 to 7.0 kΩ
    20°C (68°F)
    EGR valve is fully closed
    0.1 to 2.5 kΩ

    Text in Illustration 
    *a
    Component without harness connected
    (Electric EGR Control Valve)

    HINT:
    The resistance increases in proportion to the opening amount of the EGR valve.

    If the result is not as specified, replace the electric EGR control valve assembly.

← INSPECTION (Jun 2011 – Jul 2012)INSTALLATION (Jun 2011 – Jul 2012) →