Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.
Loosen the radiator drain cock plug.
HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.
Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.
Loosen the cylinder block drain cock plug.
7.
REMOVE FRONT WHEEL RH
8.
REMOVE FRONT FENDER APRON SEAL UPPER
Remove the 5 clips and front fender apron seal upper.
9.
REMOVE FRONT FENDER SEAL
Remove the 5 clips and front fender seal.
10.
REMOVE AIR CLEANER ASSEMBLY
Detach the wire harness clamp and disconnect the mass air flow meter connector.
Detach the ventilation hose clamp and remove the ventilation hose.
Loosen the hose clamp and disconnect No. 1 air cleaner hose from the compressor inlet elbow.
Remove the 2 bolts and air cleaner together with the No. 1 air cleaner hose.
11.
REMOVE VENTILATION HOSE CLAMP
Remove the bolt and ventilation hose clamp.
12.
REMOVE COMPRESSOR INLET ELBOW
Disconnect the 2 connectors and detach the wire harness clamp.
Remove the 2 nuts, compressor inlet elbow and gasket.
13.
REMOVE NO. 1 TURBO INSULATOR
Remove the 2 bolts and No. 1 turbo insulator.
14.
REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
Remove the bolt and No. 1 exhaust manifold heat insulator.
15.
REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
Remove the 2 bolts and No. 2 exhaust manifold heat insulator.
16.
REMOVE NO. 3 EXHAUST MANIFOLD HEAT INSULATOR
Remove the 2 bolts and No. 3 exhaust manifold heat insulator.
17.
REMOVE TURBINE OUTLET ELBOW STAY
Detach the wire harness clamp and remove the bolt, nut and turbine outlet elbow stay.
18.
REMOVE NO. 2 TURBINE OUTLET ELBOW
Remove the 3 nuts, No. 2 turbine outlet elbow and gasket.
19.
DISCONNECT NO. 1 FUEL PIPE
Detach the hose clamp and disconnect the No. 4 turbo water hose from the No. 4 water by-pass pipe.
Disconnect the exhaust fuel addition injector connector.
Remove the union bolt and gasket.
Disconnect the No. 1 fuel pipe from the turbine outlet elbow.
20.
REMOVE TURBINE OUTLET ELBOW
Disconnect the No. 3 turbo water hose from the No. 3 water by-pass pipe.
Remove the 3 nuts, turbine outlet elbow and gasket.
Text in Illustration
*1
Gasket
*2
Union Bolt
*3
No. 3 Water By-pass Pipe
*4
No. 4 Water By-pass Pipe
*5
No. 3 Turbo Water Hose
*6
Turbine Outlet Elbow
Remove the bolt, union bolt, gasket and No. 3 water by-pass pipe from the turbine outlet elbow.
Remove the union bolt, gasket and No. 4 water by-pass pipe from the turbine outlet elbow.
21.
DISCONNECT NO. 1 TURBO WATER HOSE
Disconnect the 2 No. 1 turbo water hoses.
22.
REMOVE TURBOCHARGER STAY
Remove the 2 bolts, nut and turbocharger stay.
23.
REMOVE TURBO OIL INLET PIPE SUB-ASSEMBLY
Remove the 2 bolts, 2 nuts, union bolt, turbo oil inlet pipe and 3 gaskets.
NOTICE:
Do not loosen the nut labeled A in the illustration.
24.
REMOVE TURBOCHARGER SUB-ASSEMBLY
Remove the 3 nuts, turbocharger and gasket.
25.
REMOVE NO. 1 TURBO WATER PIPE SUB-ASSEMBLY
Remove the 2 nuts, bolt, No. 1 turbo water pipe and gasket.