2014 Hilux · Service Manual BRAKE

C1268 Transfer L4 Position Switch Circuit

Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013

DESCRIPTION

DTC Code
DTC Detection Condition
Trouble Area
C1268
No signal is input to the EXI4 terminal of the skid control ECU.
  1. L4 position switch (No. 1 transfer indicator switch)
  2. L4 position switch circuit
  3. Skid control ECU (Brake actuator assembly)
  4. Transmission control ECU assembly (for 1KD-FTV)
  5. ECM (for 1GR-FE)

WIRING DIAGRAM

C237164E18
C237164E17
C190842E16

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the brake actuator assembly, perform calibration (Click here).
  2. Before disconnecting the connector, make sure that there are no problems with the connection.
  3. After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.


1. CHECK TERMINAL VOLTAGE (EXI4 TERMINAL)

  1. C199357E59
    Connect the skid control ECU (brake actuator assembly) connector.

  1. Set the vehicle to the L4 state using the transfer shift lever.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    S35-9 (EXI4) - Body ground
    1. Ignition switch ON
    2. Transfer shift position L4
    Below 1.5 V

  1. Connect the skid control ECU (brake actuator assembly) connector.

  1. Set the vehicle to the H4 or H2 state using the transfer shift lever.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    S35-9 (EXI4) - Body ground
    1. Ignition switch ON
    2. Transfer shift position not L4
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


NG
Go to step 3
OK


2. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Turn the ignition switch off.

  1. Check if the same DTC is output.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    for LHD
    B
    for RHD
    C



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

3. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - L4 POSITION SWITCH)
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. for 1KD-FTV (Automatic Transmission):Disconnect the T37 transmission control ECU connector.for 1GR-FE:Disconnect the E17 ECM connector.

  1. Disconnect the L4 position switch (No. 1 transfer indicator switch) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S35-9 (EXI4) - T4-1
    Always
    Below 1 Ω
    S35-9 (EXI4) - Body ground
    Always
    10 kΩ or higher
    T4-2 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT L4 POSITION SWITCH
  1. Turn the ignition switch off.

  1. Remove the L4 position switch (No. 1 transfer indicator switch).

  1. Inspect the L4 position switch (No. 1 transfer indicator switch) (Click here).



NG
REPLACE NO. 1 TRANSFER INDICATOR SWITCH
OK


5. CHECK TERMINAL VOLTAGE (L4 POSITION SWITCH POWER SOURCE CIRCUIT)

  1. C239113E02
    Turn the ignition switch off.

  1. Disconnect the L4 position switch (No. 1 transfer indicator switch) connector.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. for 1KD-FTV (Automatic Transmission):Connect the transmission control ECU connector.for 1GR-FE:Connect the ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to L4 Position Switch [No. 1 Transfer Indicator Switch])
    Result 
    Result
    Proceed to
    OK
    A
    NG
    for 1KD-FTV (Manual Transmission) and 2KD-FTV
    B
    for 1KD-FTV (Automatic Transmission)
    C
    for 1GR-FE
    D



B
REPAIR OR REPLACE HARNESS OR CONNECTOR

C
Go to step 6

D
Go to step 7
A

USE SIMULATION METHOD TO CHECK (Click here)

6. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - TRANSMISSION CONTROL ECU)
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Disconnect the T37 transmission control ECU connector.

  1. Disconnect the L4 position switch (No. 1 transfer indicator switch) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S35-9 (EXI4) - T37-15 (L4)
    Always
    Below 1 Ω
    S35-9 (EXI4) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

7. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ECM)
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Disconnect the E17 ECM connector.

  1. Disconnect the L4 position switch (No. 1 transfer indicator switch) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S35-9 (EXI4) - E17-13 (L4)
    Always
    Below 1 Ω
    S35-9 (EXI4) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← C1241 Low Power Supply Voltage Malfunction (from Aug 2014)C1268 Transfer L4 Position Switch Circuit (Aug 2012 – Jul 2013) →