C1268 Transfer L4 Position Switch Circuit
Diagnostic trouble codes · Vehicles built from Aug 2013
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 from Aug 2013
DESCRIPTION
| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1268 |
No signal is input to the EXI4 terminal of the skid control ECU. |
|
WIRING DIAGRAM






INSPECTION PROCEDURE
- NOTICE:
- After replacing the brake actuator assembly, perform calibration (Click here).
- Before disconnecting the connector, make sure that there are no problems with the connection.
- After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.
- After replacing the brake actuator assembly, perform calibration (Click here).
| 1. CHECK TERMINAL VOLTAGE (EXI4 TERMINAL) |
Connect the skid control ECU (brake actuator assembly) connector.

Set the vehicle to the L4 state using the transfer shift lever.
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
S35-9 (EXI4) - Body ground
- Ignition switch ON
- Transfer shift position L4
Below 1.5 V
- Ignition switch ON
Connect the skid control ECU (brake actuator assembly) connector.
Set the vehicle to the H4 or H2 state using the transfer shift lever.
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
S35-9 (EXI4) - Body ground
- Ignition switch ON
- Transfer shift position not L4
11 to 14 V
- Ignition switch ON
| *a |
Front view of wire harness connector (to Skid Control ECU [Brake Actuator Assembly]) |
|
|
||||
| OK | |
| 2. RECONFIRM DTC |
Clear the DTC (Click here).
Turn the ignition switch off.
Check if the same DTC is output.
Result Result
Proceed to
DTC is not output
A
DTC is output
for LHD
B
for RHD
C
|
|
||||
|
|
||||
| A | ||
| ||
| 3. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - L4 POSITION SWITCH) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
for 1KD-FTV (Automatic Transmission):Disconnect the T37 transmission control ECU connector.for 1GR-FE:Disconnect the E17 ECM connector.
Disconnect the L4 position switch (No. 1 transfer indicator switch) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
S35-9 (EXI4) - T4-1
Always
Below 1 Ω
S35-9 (EXI4) - Body ground
Always
10 kΩ or higher
T4-2 - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 4. INSPECT L4 POSITION SWITCH |
Turn the ignition switch off.
Remove the L4 position switch (No. 1 transfer indicator switch).
Inspect the L4 position switch (No. 1 transfer indicator switch) (Click here).
|
|
||||
| OK | |
| 5. CHECK TERMINAL VOLTAGE (L4 POSITION SWITCH POWER SOURCE CIRCUIT) |
Turn the ignition switch off.

Disconnect the L4 position switch (No. 1 transfer indicator switch) connector.
Disconnect the skid control ECU (brake actuator assembly) connector.
for 1KD-FTV (Automatic Transmission):Connect the transmission control ECU connector.for 1GR-FE:Connect the ECM connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
1 - 2
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to L4 Position Switch [No. 1 Transfer Indicator Switch])
Result Result
Proceed to
OK
A
NG
for 1KD-FTV (Manual Transmission) and 2KD-FTV
B
for 1KD-FTV (Automatic Transmission)
C
for 1GR-FE
D
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
| 6. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - TRANSMISSION CONTROL ECU) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Disconnect the T37 transmission control ECU connector.
Disconnect the L4 position switch (No. 1 transfer indicator switch) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
S35-9 (EXI4) - T37-15 (L4)
Always
Below 1 Ω
S35-9 (EXI4) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 7. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ECM) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Disconnect the E17 ECM connector.
Disconnect the L4 position switch (No. 1 transfer indicator switch) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
S35-9 (EXI4) - E17-13 (L4)
Always
Below 1 Ω
S35-9 (EXI4) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
