2014 Hilux · Service Manual BRAKE

C1282 Center Differential Lock Position Switch

Diagnostic trouble codes · Vehicles built Jun 2011 – Jul 2012

Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

DTC C1282 is stored only in Test Mode.
DTC Code
DTC Detection Condition
Trouble area
C1282
Stored during Test Mode.
  1. Harness or connector
  2. Transfer system
  3. Skid control ECU (Brake actuator assembly)

WIRING DIAGRAM

C237097E06

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the brake actuator assembly, perform calibration (Click here).
  2. Before disconnecting the connector, make sure that there are no problems with the connection.
  3. After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.


1. CHECK TERMINAL VOLTAGE (EXI TERMINAL)
  1. Connect the skid control ECU (brake actuator assembly) connector.

  1. Set the vehicle to the 4WD state using the transfer shift lever.

  1. C199357E60
    Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    S35-20 (EXI) - Body ground
    1. Ignition switch ON
    2. Transfer shift position H4
    Below 1.5 V

  1. Connect the skid control ECU (brake actuator assembly) connector.

  1. Set the vehicle to the 2WD state using the transfer shift lever.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    S35-20 (EXI) - Body ground
    1. Ignition switch ON
    2. Transfer shift position H2
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


NG
Go to step 3
OK


2. CHECK TEST MODE DTC
  1. Switch the vehicle to Test Mode, check the H2 to H4 shift operation, and then check that DTC C1282 is cleared (Click here).

    Result 
    Result
    Proceed to
    Test Mode DTC is cleared
    A
    Test Mode DTC is not cleared
    for LHD
    B
    for RHD
    C



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

3. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - 4 WHEEL DRIVE CONTROL ECU AND 4WD DETECTION SWITCH)
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Disconnect the 4WD detection switch (differential vacuum actuator assembly) connector.

  1. Disconnect the 4 wheel drive control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S35-20 (EXI) - A3-3 (ADD)
    Always
    Below 1 Ω
    S35-20 (EXI) - F14-8 (ADD)
    Always
    Below 1 Ω
    S35-20 (EXI) - Body ground
    Always
    10 kΩ or higher
    A3-4 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO TRANSFER SYSTEM (PROBLEM SYMPTOMS TABLE) (Click here)


← C1268 Transfer L4 Position Switch Circuit (from Aug 2013)C1282 Center Differential Lock Position Switch (Aug 2012 – Jul 2013) →