C1282 Center Differential Lock Position Switch
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Jun 2011 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
DTC C1282 is stored only in Test Mode.
DTC Code
|
DTC Detection Condition
|
Trouble area
|
C1282
|
Stored during Test Mode.
|
- Harness or connector
- Transfer system
- Skid control ECU (Brake actuator assembly)
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the brake actuator assembly, perform calibration (Click here).
- Before disconnecting the connector, make sure that there are no problems with the connection.
- After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.
| 1. CHECK TERMINAL VOLTAGE (EXI TERMINAL) |
 |
Connect the skid control ECU (brake actuator assembly) connector.
Set the vehicle to the 4WD state using the transfer shift lever.
- Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
S35-20 (EXI) - Body ground
|
- Ignition switch ON
- Transfer shift position H4
|
Below 1.5 V
|
Connect the skid control ECU (brake actuator assembly) connector.
Set the vehicle to the 2WD state using the transfer shift lever.
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
S35-20 (EXI) - Body ground
|
- Ignition switch ON
- Transfer shift position H2
|
11 to 14 V
|
Text in Illustration
*a
|
Front view of wire harness connector (to Skid Control ECU [Brake Actuator Assembly])
|
|
NG |
 |
|
|
|
| OK |
|
 |
|
| 2. CHECK TEST MODE DTC |
 |
Switch the vehicle to Test Mode, check the H2 to H4 shift operation, and then check that DTC C1282 is cleared (Click here).
Result
Result
|
Proceed to
|
Test Mode DTC is cleared
|
A
|
Test Mode DTC is not cleared
|
for LHD
|
B
|
for RHD
|
C
|
|
B |
 |
|
|
|
|
C |
 |
|
|
|
| A |
|
 |
|
|
| 3. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - 4 WHEEL DRIVE CONTROL ECU AND 4WD DETECTION SWITCH) |
 |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Disconnect the 4WD detection switch (differential vacuum actuator assembly) connector.
Disconnect the 4 wheel drive control ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
S35-20 (EXI) - A3-3 (ADD)
|
Always
|
Below 1 Ω
|
S35-20 (EXI) - F14-8 (ADD)
|
Always
|
Below 1 Ω
|
S35-20 (EXI) - Body ground
|
Always
|
10 kΩ or higher
|
A3-4 (GND) - Body ground
|
Always
|
Below 1 Ω
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| GO TO TRANSFER SYSTEM (PROBLEM SYMPTOMS TABLE) (Click here)
|
|