Slip Indicator Light does not Come ON
Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Jun 2011 – Oct 2011 Nov 2011 – Mar 2012 Apr 2012 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
Refer to Slip Indicator Light Remains ON (Click here).WIRING DIAGRAM
Refer to Slip Indicator Light Remains ON (Click here).INSPECTION PROCEDURE
- NOTICE:
- After replacing the brake actuator assembly, perform calibration (Click here).
- Before disconnecting the connector, make sure that there are no problems with the connection.
- After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.
- After replacing the brake actuator assembly, perform calibration (Click here).
| 1. CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED |
Check if the skid control ECU connector is securely connected.
- OK:
- The connector is securely connected.
|
|
||||
| OK | |
| 2. CHECK TERMINAL VOLTAGE (IG1 TERMINAL) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
S35-34 (IG1) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (GND1 TERMINAL) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
S35-1 (GND1) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Disconnect the C26 combination meter connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
S35-3 (IND) - C26-17
Always
Below 1 Ω
S35-3 (IND) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SLIP INDICATOR LIGHT) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
ABS/VSC/TRC Tester Display
Test Part
Control Range
Diagnostic Note
Slip Indicator Light
Slip indicator light
Indicator light ON / OFF
Observe the combination meter.
When performing the Slip Indicator Light Active Test, check Slip Indicator Light in the Data List.
| Tester Display |
Measurement Item / Range |
Normal Condition |
Diagnostic Note |
| Slip Indicator Light |
Slip indicator light / ON or OFF |
ON: Slip indicator light on OFF: Slip indicator light off |
- |
| Result |
Proceed to |
||
| Data List Display |
Data List Display When Performing Active Test ON/OFF Operation |
||
| ON |
Does not change between ON and OFF |
for LHD |
A |
| Does not change between ON and OFF |
for RHD |
B |
|
| Changes between ON and OFF |
C |
||
| OFF |
Does not change between ON and OFF |
for LHD |
A |
| Does not change between ON and OFF |
for RHD |
B |
|
| Changes between ON and OFF |
C |
||
|
|
||||
|
|
||||
| A | ||
| ||
