VSC OFF Indicator Light does not Come ON
Circuit diagnosis · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Jun 2011 – Oct 2011 Nov 2011 – Mar 2012 Apr 2012 – Jul 2012 Aug 2012 – Jul 2013 Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
Refer to VSC OFF Indicator Light Remains ON (Click here).WIRING DIAGRAM
Refer to VSC OFF Indicator Light Remains ON (Click here).INSPECTION PROCEDURE
- NOTICE:
- After replacing the brake actuator assembly, perform calibration (Click here).
- Before disconnecting the connector, make sure that there are no problems with the connection.
- After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.
| 1. CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED |
 |
Check if the skid control ECU (brake actuator assembly) connector is securely connected.
- OK:
- The connector is securely connected.
|
NG |
 |
|
| CONNECT CONNECTOR TO ECU CORRECTLY |
|
|
| OK |
|
 |
|
| 2. CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
|
 |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
- Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
|
Switch Condition
|
Specified Condition
|
S35-34 (IG1) - Body ground
|
Ignition switch ON
|
11 to 14 V
|
Text in Illustration
*a
|
Front view of wire harness connector (to Skid Control ECU [Brake Actuator Assembly])
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| 3. CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
|
 |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
S35-1 (GND1) - Body ground
|
Always
|
Below 1 Ω
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| 4. INSPECT VSC OFF SWITCH
|
 |
Turn the ignition switch off.
Remove the VSC OFF switch (Click here).
Inspect the VSC OFF switch (Click here).
|
NG |
 |
|
|
|
| OK |
|
 |
|
| 5. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)
|
 |
Turn the ignition switch off.
Disconnect the VSC OFF switch connector.
Disconnect the skid control ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
S35-30 (CSW) - V8-3
|
Always
|
Below 1 Ω
|
S35-30 (CSW) - Body ground
|
Always
|
10 kΩ or higher
|
V8-4 - Body ground
|
Always
|
Below 1 Ω
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| 6. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)
|
 |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Disconnect the C26 combination meter connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
S35-15 (VSCW) - C26-16
|
Always
|
Below 1 Ω
|
S35-15 (VSCW) - Body ground
|
Always
|
10 kΩ or higher
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| 7. INSPECT COMBINATION METER ASSEMBLY |
 |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
- Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
|
Switch Condition
|
Specified Condition
|
S35-15 (VSCW) - Body ground
|
Ignition switch ON
|
11 to 14 V
|
Text in Illustration
*a
|
Front view of wire harness connector (to Skid Control ECU [Brake Actuator Assembly])
|
Result
Result
|
Proceed to
|
NG
|
A
|
OK
|
for LHD
|
B
|
for RHD
|
C
|
|
B |
 |
|
|
|
|
C |
 |
|
|
|
| A |
|
 |
|
| GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
|
|