2014 Hilux · Service Manual BRAKE

TRC OFF Indicator Light does not Come ON

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Refer to TRC OFF Indicator Light Remains ON (Click here).

WIRING DIAGRAM

Refer to VSC OFF Indicator Light Remains ON (Click here).

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the brake actuator assembly, perform calibration (Click here).
  2. Before disconnecting the connector, make sure that there are no problems with the connection.
  3. After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.


1. CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU (brake actuator assembly) connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


2. CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. C199357E58
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    S35-34 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU [Brake Actuator Assembly])



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S35-1 (GND1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT VSC OFF SWITCH
  1. Turn the ignition switch off.

  1. Remove the VSC OFF switch (Click here).

  1. Inspect the VSC OFF switch (Click here).



NG
REPLACE VSC OFF SWITCH (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)
  1. Turn the ignition switch off.

  1. Disconnect the VSC OFF switch connector.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S35-30 (CSW) - V8-3
    Always
    Below 1 Ω
    S35-30 (CSW) - Body ground
    Always
    10 kΩ or higher
    V8-4 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - COMBINATION METER)
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Disconnect the C26 combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S35-23 (INFR) - C26-21
    Always
    Below 1 Ω
    S35-23 (INFR) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. INSPECT COMBINATION METER ASSEMBLY
  1. Turn the ignition switch off.

  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. C288996E03
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    S35-23 (INFR) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU [Brake Actuator Assembly])
    Result 
    Result
    Proceed to
    NG
    A
    OK
    for LHD
    B
    for RHD
    C



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)


← TRC OFF Indicator Light does not Come ON (Aug 2013 – Jul 2014)VSC OFF Indicator Light Remains ON (Jun 2011 – Oct 2011) →